BRIGGS & STRATTON CORPORATION

An employee was working on a belt-driven coolant pump when his left hand was caught in the belt, resulting in lacerations and fractures. He was hospitalized and required surgery.

An employee was changing a water hose on a die machine. The employee had extended the ram of the machine fully to gain access to the water line. As the employee was checking the water hose, the hydraulics on the ram released, causing the ram to retract to its holding position. The ram caught the employee's hands, pinned them, and broke bones in both hands.

An employee was on a fiberglass step ladder, about 3 feet off the ground, capping off a dead air line. The employee fell off the ladder and suffered two broken ribs, a punctured lung, and head trauma.

An employee was asked to help perform maintenance on a die cast machine. The employee entered the work area, got into a kneeling position, and began using an open-end wrench to remove a hydraulic hose so a fitting could be repaired. When the hose came free from the fixture, residual hydraulic pressure released and hydraulic fluid struck the employee in the chest. The employee fell backward and struck his head on surrounding machinery. The employee was hospitalized with a subdural hematoma, fractures to the forehead, orbital area, and ribs, and required stitches for a forehead laceration.

A trim die was being transported by a forklift. When the die was placed on the ground, the top part of it popped off and crushed an employee's hand against a set of metal stairs. The employee suffered a laceration to the right hand between the thumb and the index finger.

An employee was adjusting a blade on a padder machine. As he manually turned a roller, his hand contacted the blade, amputating his right thumb tip.

An employee was cleaning a slicer when the tip of their right index finger was amputated, requiring hospitalization.

An employee was tying a feed bag when his hand slipped and struck the side of the feed hopper resulting in a laceration to the left wrist. The employee was hospitalized.

At approximately 9:45 AM, a maintenance technician was assisting in removing a feed roller from a coating tank. The bolts were removed and a supporting chain was in place. The technician was using a prybar to unseat the roller shaft when the prybar slipped, causing him to lunge forward and strike the right side of his face against a valve stem. The technician sustained a fracture and laceration to the cheek, and required surgery for an injury related to his right eye. He was hospitalized.

An employee was cleaning and performing maintenance on a vertical panel saw when the employee impacted the saw blade. They sustained a finger fracture and laceration.

An employee was moving a hoist to the end of a bridge rail to create space for another hoist on the same rail. The hoist being moved, along with its supporting beam, detached from the bridge rail and fell, striking the employee in the head. He suffered a contusion and laceration to the head and was hospitalized.

An employee was operating a machine. When they performed a motion to push a machined engine block away from their body, they experienced a back strain, resulting in hospitalization.

On September 13, 2025, an employee had been working at an outdoor event. At the end the day, she was walking around outside the facility to make sure everything was put away and felt overheated. The employee was hospitalized for heat-related illness.

An employee was installing insulation in a wall panel when the panel fell on top of them, resulting in leg and back injuries that required hospitalization.

An employee put a cylinder machining pallet into manual mode to unjam it. After completing the task, their left hand became lodged between a pulley and belt, resulting in the amputation of three fingers.

An employee was helping to lift the grating from a floor draining system when the grating slipped and landed on his hand, resulting in the amputation of his right middle finger at the first joint.

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

During a workshop meeting in a hotel, an employee heard a drilling noise, so he walked outside to see what it was. An explosion occurred (possible gas line) and his face, ear, and hair were burned. He also fell and sustained a pelvic fracture.

An employee slipped on condensation on a walkway in a parking garage. She fell and suffered a closed fracture to the neck of the left femur.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.