Kelley Steel Erectors, Inc.

An employee was using an electric grinder on a weld joint, opening up the joint on the bottom flange of a steel beam. The grinding disk caught an edge of the beam, kicked back, and lacerated the employee's neck. He was hospitalized.

An employee's foot was run over and crushed by a telehandler.

An employee was moving a piece of steel to its landing position when his left fourth digit fingertip was caught between the steel and its landing position, resulting in a fingertip amputation.

An employee was lighting an oxy-propane torch when a leak allowed a flame to propagate up the employee's arms, burning them.

An employee was on an 8-foot step ladder performing maintenance tasks when he fell off the ladder to the platform below and rolled down 21 feet into an unguarded pit. He broke his left arm and leg.

An employee was performing oversight for the welding of a pipeline launcher door on a construction project. Two welders were performing arc welding, one on the interior diameter of the pipeline launcher door, and the other on the outside diameter of the launcher door when a flash fire occurred. The injured employee sustained first- and second-degree burns to the face, neck, back, and hands.

While on a scissor lift, an employee was grinding a steel pipe. Sparks from the grinder ignited some nearby rags that had been used to apply coating treatments to the pipe. This fire subsequently ignited the employee's clothing. The employee sustained burns to approximately 46% of their body and was hospitalized.

An employee was working in an area where another company was also working. The other company's employees were using an electric hydraulic pump to remove the bolts of the frac valve. The wiring of the torque wrench and pump unit were then charred and a flash fire occurred. The employee sustained second-degree burns to their face and neck.

On October 17, 2023, an employee was at a sink while using a solvent to unclog a vacuum trap dip tube that contained solids from pinacolborane distillation. During this process, the sink caught on fire and the solvent bottle containing tert-butyl methyl ether fell into the burning sink. The employee attempted to remove the solvent bottle which also caught on fire and suffered burns to their neck and left hand.

An employee was under a railcar cleaning up dust with a vacuum hose. The hose caused a spark that caused a flash fire that ignited the employee's clothing. The employee sustained second- and third-degree burns over 83% of his body.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was working to deliver mail to an apartment building. She was waiting for a customer to move, to obtain clearance to the mailboxes. The door swung inward and closed on her right little finger. The top half of her finger was surgically amputated.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

On October 30, 2025, an employee was working to adjust a stackable metal shipping container. As the container dropped into place, it caught the employee's hands in an area between the upper and lower cross-members. The employee suffered a laceration to the left ring finger that required stitches, bruising to the right ring finger, and fractures to the right middle finger that necessitated medical amputation of the fingertip.

An employee was moving a scissor lift through a doorway. The employee was pinned between the scissor lift and the doorframe, sustained a back injury, and was hospitalized.

An employee was setting up communication equipment for a meeting. They were walking and tripped over a speaker on the ground. The employee sustained a leg injury.