M-B Companies, Inc.

On September 28, 2018, at 8:00 a.m. two employees were working together to install an exhaust pipe on the rear engine compartment of airport-sized snow removal equipment. The injured employee was working from an attached catwalk on the snow removal equipment to install the exhaust pipe while the other employee was on the roof of the equipment to hold the top of the pipe and secure a bolt. While installing the exhaust pipe, the injured employee stepped back and fell approximately 59 inches landing on the concrete floor below. He was hospitalized for a severe concussion, broken vertebrae in the neck and a shoulder injury.

An employee was operating a forklift and unloading a truck. After the truck was unloaded, the employee got off the forklift and proceeded to adjust the dock plate with a hook tool. The dock plate slipped and the employee went to adjust the plate with their hand when their left middle finger got caught. Their finger was amputated above the first joint.

An employee was rotating a carbide granulator blade when his finger was caught between the blade and a stationary part of the machine. The employee's right middle finger was partially amputated and they suffered an avulsion to the right ring fingertip.

An employee was using a CNC metal lathe machine in manual mode to check that the thread blocking tool made contact with the jaws. As the employee was manually spinning the spindle, his index fingertip was crushed between the spindle's jaws and the grooving insert, resulting in a fingertip amputation.

During a material handling operation, an employee's fingertip was caught under an air conditioning unit as the unit was lowered onto a cart. The employee's fingertip was amputated.

An employee was removing a bolt from a tractor hub when their right index finger was caught between the hub and the frame. The employee's fingertip was crushed and the employee was hospitalized.

An employee was working behind a stack of steel I-beams (stacked 2 columns deep and 4 levels high on the floor) while a forklift was pushing the stack. When the forklift took off the second-to-last beam, the last one was pushed over, causing it to fall to the ground and strike the employee. The employee sustained a fracture to the right leg.

An employee was lifting a flat sub (sheet steel) in the flats robot cell (weld area). He was operating a hoist when his left little fingertip got caught between the lifting device hook and the flat sub. The employee sustained a partial transphalangeal amputation.

An employee was underneath a 35-foot boom truck and adjusting the transmission linkage when the truck jumped over the wheel chocks and rolled over the employee's right leg, resulting in a fracture.

A crane was being used to lift a debris tank from a rack. The tank crushed the employee's right hand, causing amputations to the employee's right ring finger and little fingertip.

An employee was removing a small sheet metal part out of the die of the brake press. The foot pedal was pressed, causing the part to lift and crush their left thumb against the die. The employee suffered an amputation to the thumb tip including the loss of flesh and the fingernail.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.