Standard Concrete Products Inc

An employee was adjusting and stabilizing an oil tank that was being set into a containment bin by a telehandler when the employee's arm was caught between the tank and the containment wall. The employee sustained a left forearm fracture.

An employee was lubricating a concrete mixer when they were struck by an energized paddle. The employee sustained lacerations and a fracture to the forearm.

An employee was standing on a 24-inch-high concrete block when he fell backward, resulting in abdominal bruising.

An employee was adjusting wooden dunnage under concrete piling when the pile unexpectedly shifted due to a wind draft. The employee was then caught between a metal form and the concrete pile, fracturing his pelvis.

An employee was participating in concrete stress testing operations. A stress cable retention chuck slipped causing the cable end to flip and puncture the employee's right hand and abdomen.

An employee was unloading a trailer when a box fell and struck the employee in the face. The employee suffered a concussion and was hospitalized.

An employee had been cutting lumber for a shed wall. A load of 16-foot trim pieces fell onto the employee causing vertebrae and ankle fractures.

An employee was unloading 30-foot 2-inch barrels from a pan holding about 20 barrels. The barrels tipped over, striking and breaking both of the employee's lower legs.

An employee was in a sandblasting area, preparing the surface of a plate heat exchanger frame for painting. The frame fell on the employee, who suffered fractures to vertebrae, the neck, pelvis, and rib cage; and punctured lungs.

An employee was installing doors when one of the doors fell on him, fracturing his lower leg. The employee was hospitalized.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was helping a coworker transport a tall palm tree with a mini skid steer. The employee was severely shocked by a high-voltage electrical wire above the ground.

An employee was retrieving a Christmas tree from a shelf using a ladder. He missed a step and fell to the concrete floor. He sustained injury to his head and wrist.

An employee was inspecting a generator whose radiator was leaking. He slipped, and a fan blade in the generator amputated his thumb and index finger.

An employee was operating an agricultural tractor during sugarcane harvesting. The employee sustained a lumbar sprain due to vibration or motion from the tractor.

An employee was moving a 3-ton condensing unit, strapped down on a dolly, out of a garage. The strap broke, causing the employee to fall backward onto the brick pavered driveway. The employee suffered injury to a spinal ligament in the neck.