Tulsa Tube Bending Co., Inc.

The injured employee was loading a piece of pipe into a pipe bending machine. He had his right hand on the front of the loader while his left hand supported the piece of pipe in the back. A second operator had slightly clamped around the pipe to keep it in place. The third operator called out a measurement. The machine actuated and caught the the injured employee's left middle and ring fingers between the wiper and the material. The employee required surgery and sustained amputations to the distal joint of the middle and ring fingers.

An employee was using an ironworker machine to cut angle iron when something jerked and pushed his left middle finger into the machine. The employee's fingertip was amputated.

A crew was pulling a 4-inch plastic gas pipe off a reel and straightening it for installation. The injured employee stepped up on the trailer to cut the last band holding the pipe in the coil on the reel. As he turned to step off the trailer, the end of the pipe rotated and sprung out of the cage surrounding the coil, striking the employee on the side of the head and knocking him off of the trailer into the roadway. The employee suffered head trauma that required hospitalization.

An employee and a co-worker were performing a pick inside a clear well. They rigged the skid pan that was full of broken concrete. When lifting, the load began to swing toward a wall. The employee tried to stop the skid pan from swinging and was struck by the pan, resulting in fractures to their left hip and wrist.

The employee had just completed refueling a lattice crane that was breaking up material and was winding the fuel hose back into the fuel truck when he was struck by the catwalk/stairs of the crane. The employee was hospitalized with a laceration to his backside, possible internal bleeding, and a broken hip.

An employee was fusing 10-inch black rubber utility pipes together using a pipe fusion machine and could not get the pipes to set correctly. The employee used a nylon strap attached to an excavator to lift one side of a pipe off a steel plate. As his hand was between two pipes, the pipes came back together, partially amputating two of his fingers.

An employee was lifting four bags of a lime blend weighing approximately 10,000 pounds using a crane. The load swung and pinned the employee against a structural I-beam, resulting in fractures to the hip and pelvis.

An employee was rolling a pipe in a cutting rack and his right little finger became caught between sections of the pipe. The employee's finger was surgically amputated.

An employee was working a vertical bandsaw, cutting half-inch diameter rods into pieces. While using a steel chisel to move the cut pieces, the blade caught his leather glove and pulled his index finger in. The employee sustained an amputation of the finger between the first and second knuckle.

An employee was operating a lathe in a machine shop. The rotating head of the lathe caught the employee's left glove, resulting in a compound open fracture to the left wrist and a laceration to left ear.

An employee was descending the stairs of an oil/gas rig. As he approached the fifth step from the bottom, he slipped. His left ankle was caught in the steps, and he suffered fractures to the left fibula, tibia, and talus. He was hospitalized, requiring surgery.

The injured employee was loading a piece of pipe into a pipe bending machine. He had his right hand on the front of the loader while his left hand supported the piece of pipe in the back. A second operator had slightly clamped around the pipe to keep it in place. The third operator called out a measurement. The machine actuated and caught the the injured employee's left middle and ring fingers between the wiper and the material. The employee required surgery and sustained amputations to the distal joint of the middle and ring fingers.

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

An employee was working in the food service warehouse when he experienced chest pain, difficulty breathing, and lost consciousness. The employee sustained carbon monoxide poisoning.

An employee was cutting a piece of metal rod with a metal cutting machine. His right middle finger became caught between the rod and the machine's table. The employee's fingertip was partially amputated.

An employee was working at her desk. She went to stand up and fell to the floor beside the desk. The employee sustained a hip displacement and required surgery.

An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.