Hancock Lumber Company Inc

An employee was sawing a board using a molder saw when the board jammed. The employee was removing the board when their right index finger was amputated at the distal knuckle and the middle finger was injured.

An employee was climbing a step ladder while carrying a 3-foot piece of conduit. As he went to reposition his feet on the ladder by pivoting, he slipped and fell from the third rung of a 6-foot ladder. The employee sustained fractures to the left femur, right elbow, and right ring finger.

An employee was descending a 4-step maintenance stand when she missed the bottom step and fell to the hangar floor. The employee suffered a left hip fracture.

An employee stopped a belt and was going to check it for missing packages. She fell backward 3-4 feet from an elevated platform and sustained a broken right arm.

An employee had just finished a routine concrete pour and was ascending the ladder to clean the concrete mixer truck. The employee lost their grip and fell approximately 2-3 feet, contacting the truck's bumper. The employee suffered rib fractures and a punctured lung.

An employee was performing duties as an expeditor. After opening the dock door, the employee scanned the barcode on the door of the truck and placed one foot on the truck and one foot on the dock. The truck drove out of the stall, causing the employee to fall 4 feet off the dock onto the concrete. The employee sustained fractures to the right side of the pelvis, elbow, and a left ring fingertip as well as injuries to the right wrist and bruising to the back and stomach.

On May 9, 2025, an employee was using an air hose to clear debris from the courtyard area when she slipped and fell. The employee was hospitalized with closed fractures to her left fibula, tibia, and medial malleolus.

On April 24, 2025, an employee was opening a cylinder door on a hydraulic bridge to remove lumber when their left middle finger was caught between the door and the hydraulic bridge, resulting in an amputation without bone loss.

Two employees were using a plywood chop saw. The injured employee was holding one end of the saw with their right hand when the operator on the other end pressed the start button. The saw blade contacted the injured employee's right hand, resulting in multiple finger amputations when it amputated the hand above the thumb.

On January 17, 2025, at 12:15 p.m., an employee was moving 11-gauge steel sheets from a holding cart using a pendant-controlled, 1-ton jib hoist equipped with a plate clamp lifting attachment. With the plate clamp empty and open, the employee began raising the hoist. The clamp became caught on the bottom of the cart, tipping the cart in the direction of the employee. Several sheets of steel slid off the cart and struck the employee, resulting in several broken ribs, a broken left leg and ankle, a fractured kneecap, and a torn left ACL. The employee was hospitalized.

An employee was operating an air hoist to rotate a blending mill counter-clockwise. After he connected the hook to the mill, the hoist was raised and his hand was pinched between the hook block and the ring on the mill. The employee sustained a partial amputation of his right thumb.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.