Commercial Metals Company

A rolling mill was shut down due to a cobble between two mill stands. The injured employee was cleaning the cobble from the delivery side of stand A, while another employee went to the control panel to move stand B and stand A moved instead. The injured employee's right thumb got caught between the delivery guide of stand A and the looper trough. The tip of his thumb required surgical amputation to the bone to allow for stitches.

A truck driver was walking on top of a load of logs to remove tarps. He approached the edge to prepare for dismounting. He stepped on a sideboard that shifted, causing him to fall to the ground. He sustained a cut to the top of his head that required five stitches, fractures to his right forearm, and a dislocated right elbow.

An employee entered the baghouse to take dust samples from a compartment. When he entered the building there was baghouse dust approximately 12 inches deep on the floor. The employee walked through the dust about 5 feet when he noticed the layer of dust beneath the top was hot and felt his feet burning. Heated dust had entered the top of his boot and worked downward until resting underneath the arch of his right foot causing burns to the bottom of his foot.

An employee was working between railcars on an active railroad track to connect the airbrake. Another employee moved the railcars, striking and running over the employee resulting in amputation of both legs.

On February 11, 2022, an employee was using an overhead crane to lift a hopper full of scraps to empty it in a dumpster that measured 40 feet long and 2 feet high. Since the dumpster was not completely full, the hopper did not dump forward, so the employee went inside the dumpster and attempted to rock the hopper. He exited the dumpster and used the overhead crane to turn the hopper to the rear of the dumpster. He then stood on the right side of the dumpster while holding onto the lifting yoke for the hopper with his right hand. While holding the yoke arm for balance, he attempted to tip the bucket by rocking it back and forth. As the bucket dumped scrap metal, his right ring finger got caught between the yoke arm and the yoke stop plate of the hopper, resulting in an amputation of the fingertip without bone loss.

An employee was using a crane. The hook slipped and a fitting fell onto a finger on the employee's left hand causing a fracture and laceration.

An employee was transporting an 800-pound die on a cart from the tool room. The employee was pulling the cart when it struck a metal plate on the floor. This caused the cart to tip forward and the die to slide off the cart. The die struck the employee's left foot and their second toe was amputated.

An employee was using a forklift to load pallets of product on a trailer. He exited the forklift to adjust a pallet by hand. The pallet fell on him, resulting in an injury to the left leg.

An employee was lifting a 500-pound steel counterweight off a pallet using a magnetic hold jib crane. The counterweight detached from the crane and the employee sustained a left foot/toe fracture that required surgery.

An employee was using a pipe wrench to turn a 42-foot-long steel pipe on jack stands to weld the bottom portion. The pipe fell off the stands, striking the injured employee on his left shin. The employee sustained a left leg fracture at the shin area as well as a tibia fracture that required surgery.

An employee was pulling a steel parts handcart when its wheels caught on something and locked up. The cart fell backward. The cart handle struck the middle of the employee's right foot, breaking bones. The employee was hospitalized and required surgery.

An employee was cutting wood with a circular saw. The saw kicked back, and its blade cut three fingers on the employee's right hand, resulting in an amputation.

An employee was installing a door from an A-frame ladder. He fell from the ladder, landed on his feet about 8 feet below, and suffered a broken tibia.

An employee was leaving the building at the end of the day when she missed a step and fell, fracturing her right foot.

Two employees were running a CNC folder machine. The injured employee went to adjust the metal and the machine came down, crushing her forearms. Her left arm was fractured and both arms required stitches.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.