Bracken Construction

An employee was helping to move a welding machine. He stumbled and fell under the tongue of the trailer, which then fell on the employee. The employee sustained fractures to both bones in their right lower leg.

While decking on the roof, an employee became overheated and required hospitalization for heat exhaustion.

An employee was collecting trash when they were struck by a rolling utility trailer. The employee sustained a right ankle fracture.

An employee was unrigging steel when an 8-inch by 50-foot, 4,875-pound piece of steel rolled onto their left leg, resulting in a fracture.

An employee was connecting a dolly to a trailer. The equipment rolled away, causing the employee's left index finger to be crushed between the trailer and the dolly. The employee sustained amputation of the fingertip.

On October 17, 2023, at 9:55 p.m., an employee was working on a ramp while moving merchandise from a cargo loader to a dolly. The employee was putting the locks on the dolly and transferring a unit load device containing packages when she realized the lock was in the down position. As she attempted to fix the lock, the unit load device started moving toward the dolly, and the employee became wedged between the dolly and the device. The employee suffered an injury to her lower left leg.

Two employees were shaking out steel beams and standing them vertically. One beam was hit, causing the other beams to fall. A beam then rolled over an employee's left shin and fractured it. The employee was hospitalized and required surgery.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.