Caught in or compressed by equipment or objects, unspecified · Traumatic injuries and disorders, n.e.c.
At a glance
Federal OSHA recorded a severe workplace injury
at Nabors Drilling Technologies USA, Inc, Rig X26, MONTROSE, PENNSYLVANIA 18801
on — Traumatic injuries and disorders, n.e.c., affecting the arm(s), unspecified.
Final narrative
An employee was picking up a 5-foot, 950-pound pneumatic cylinder (mud bucket) by the handle to move it. The employee was positioning the bucket for use when their left arm became caught between it and an iron roughneck. The employee was hospitalized with compartment syndrome that required surgery.
HospitalizedArm(s), unspecifiedOil drilling rigs and machinery
More severe injuries at Nabors Drilling Technologies USA, Inc
An employee was inserting drilling slips in a wellbore. The drill pipe separated, moved within the wellbore, and struck the employee's head. The employee suffered head trauma.
An employee was applying thread protector covers and moving the floor wrench into a stow position so they could lay pipe down. The wrench crushed the employee's hand between the wrench housing and a pipe.
An employee connected a pipe elevator to a drill string. The pipe elevator unlatched while the string was being lifted. The elevator struck the employee causing a fracture and dislocation to their right elbow. The employee was hospitalized.
An employee was removing tubulars from a mousehole but the slips did not release from the tubular until it was raised. When the slips released, they slid down the tubular and struck the employee in the head. The employee sustained a back injury, a head laceration, and a fractured rib.
An employee was climbing the derrick girt to perform work on a cover. As they went to tie off the top drive, the driller came down with the top drive pulling the employee off the girt and onto the top drive. The employee sustained fractures to the pelvis and tailbone.
An employee was changing mud cups in the hopper cylinders of a concrete pump truck. The cylinders moved and three of the employees fingers were amputated.
An employee was standing on the rig floor next to a polishing unit. His hand was placed on the polishing unit when the pump was lowered, resulting in amputation of their right thumb, ring, and middle fingertips.
An employee was using air to blow out the air wash to the blender and grinder station. As the employee reached to verify that the air wash was clean, the unit pinched and amputated their fingertip.
An employee was retrieving a lost drill pipe with a lifting bail when their left thumb got pinched between the table and handle of the lifting bail while trying to re-thread the pipe to lift it out. The employee suffered an amputation to the left thumb.
An employee was removing a core chuck from a stationary roll when their right ring finger was pinched between the chuck and the roll. The employee's fingertip was amputated.
More severe injuries in this industry (NAICS 213111)
An employee was stepping down off a 6-inch containment platform to finish loading his truck, when his right ankle rolled. The employee sustained a fractured tibia and fibula at the right ankle and required surgery.
A service crew was pulling a pump and motor from a well. After breaking a joint of pipe loose from another joint, an employee grabbed the chain tongs to prevent the pipe from spinning in the well, so the crew could continue taking it apart. The bolt that attaches the chain to the handle of the chain tongs broke, causing the chain to swing around and strike the employee's lower right leg. The chain severely punctured his leg and fractured his tibia.
An employee arrived on location and loaded a blow-out-preventer (BOP) on a 1-ton flatbed truck. While standing on the flatbed securing the the BOP, the employee stepped into a void/hole on the flatbed surface. This caused him to lose balance and fall off the truck bed with his leg still caught in the hole. As a result, he sustained fractures to his left leg.
An employee was rigging up a location. He was using an Allen wrench to free up rotation and start the drawworks engine manually. The engine rotated and his left little finger became caught between the Allen wrench and the engine. The employee sustained an amputation to his little finger and fractures to his wrist.
An employee was walking into the motor control center (MCC) room when his right ring finger was caught in the hinge of a doorway. He sustained an open phalanx fracture, which resulted in a partial amputation above the first knuckle.
An employee was changing the spacing on a telehandler's forks. A fork slipped, and the employee's left index finger was caught between it and the mast. The fingertip was medically amputated at the first knuckle.
An employee was pulling down a broken skid with a forklift. When the employee backed up the forklift to get the forks out of the skid he pulled down, he contacted the forks of another parked forklift, fracturing both of his legs. He was hospitalized.
An employee was carrying cups back to the kitchen when her foot got caught on a cart and she fell face-first. During the fall, a piece of glass from a cup cut the inside of her mouth, severing an artery. She also sustained a laceration on her lower lip. The employee was hospitalized.