Struck by dislodged or detached object(s) · Traumatic injuries or exposures unspecified
At a glance
Federal OSHA recorded a severe workplace injury
at 48forty Solutions, 4201 Grand Avenue, PITTSBURGH, PENNSYLVANIA 15225
on — Traumatic injuries or exposures unspecified, affecting the Exterior and musculoskeletal structures of the neck.
Watch 48forty Solutions — freeGet an email when a new federal OSHA severe-injury report for 48forty Solutions is published. One employer, no account, unsubscribe in one click.
Final narrative
An employee began his shift by turning on a pallet stacking machine so that the hydraulics could warm up. The machine then ejected a stack of pallets. As the employee was walking around the outfeed conveyor to turn on additional machines, he was struck by the falling stack of 21 pallets. The employee suffered a neck injury that required surgery.
Hospitalized Exterior and musculoskeletal structures of the neck Variable restraint containers n.e.c.
An employee was clearing a jam from the platform of a chop saw when the wood sweep engaged, pinning their right foot. The employee was hospitalized with a laceration and fracture to the right foot.
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
A service crew was pulling a pump and motor from a well. After breaking a joint of pipe loose from another joint, an employee grabbed the chain tongs to prevent the pipe from spinning in the well, so the crew could continue taking it apart. The bolt that attaches the chain to the handle of the chain tongs broke, causing the chain to swing around and strike the employee's lower right leg. The chain severely punctured his leg and fractured his tibia.
An employee was using a handheld grinder to cut a bolt. The grinding wheel broke apart and a fragment struck the employee s right hand, causing a laceration to the palm near the little finger.
An employee was operating a brake press when the top die broke, causing the bottom die to roll out and onto the employee's legs. Both of the employee's legs were crushed below the knee, and both legs were partially amputated. The employee's left leg was also fractured above the knee.
A pressurized aircraft nose landing gear strut assembly was being disassembled. The gland nut dislodged under pressure and made contact with an employee's left hand, breaking it.
More severe injuries in this industry (NAICS 321920)
An employee was cutting wood with a miter saw when their clothing was pulled into the blade, resulting in a bicep laceration. The employee was hospitalized. The blade cover was not in place at the time of the incident.
Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.
An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.
An employee was operating a bubble wrap production line. He was splicing the ends of the film rolls together with tape when a driven roll contacted his hand. His hand and arm were pulled into the machine up to his shoulder. The employee's forearm contacted the the hot surface (230-500 F) of the bubble stamping cylinder. He was hospitalized with burns to the forearm that required surgery and crushing injuries to the hand and forearm without fractures.
An employee was operating a pallet dismantling saw. A board became stuck, and the employee tried to pull the pallet. When the board broke, the employee's right hand made contact with the blade, resulting in the amputation of the right middle finger above the second knuckle.
An employee was walking into the motor control center (MCC) room when his right ring finger was caught in the hinge of a doorway. He sustained an open phalanx fracture, which resulted in a partial amputation above the first knuckle.
An employee was changing the spacing on a telehandler's forks. A fork slipped, and the employee's left index finger was caught between it and the mast. The fingertip was medically amputated at the first knuckle.
An employee was pulling down a broken skid with a forklift. When the employee backed up the forklift to get the forks out of the skid he pulled down, he contacted the forks of another parked forklift, fracturing both of his legs. He was hospitalized.
An employee was carrying cups back to the kitchen when her foot got caught on a cart and she fell face-first. During the fall, a piece of glass from a cup cut the inside of her mouth, severing an artery. She also sustained a laceration on her lower lip. The employee was hospitalized.