Compressed between running equipment and other object(s) · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at Wilsonart LLC, 10501 NW HK Dodgen Loop, TEMPLE, TEXAS 76504
on — Fractures , affecting the Rib(s), oblique area.
Final narrative
The injured employee and a co-worker were loading a pallet of material onto a rack using a hydraulic lift system. The employee on the south side of the lift picked up the board about 2 inches so the board could enter the rack. The employee on the north side of the lift pressed the travel button to align the board with the rack opening. The injured employee was pinned between the lift and the rack and sustained fractured ribs.
Hospitalized Rib(s), oblique area Elevators, hoists, lifts unspecified
An employee was dropping off a skid of laminate to be cut at a table saw. The skid was lifted and the forks tilted forward when the stack slid forward and struck the injured employee. The employee was pinned between the laminate and the table of the saw, resulting in a back fracture and a laceration to the liver.
An employee was standing on a 4-by-8 wooden pallet on the forks of a forklift, elevated to the second level of a rack. While pulling a cabinet off the shelf, the employee fell. He landed on the floor 7 or 8 feet below and suffered an injury to his heel.
An employee was inspecting the belt of a building exhaust fan on a roof. His left middle finger was pinched between the belt and the pulley and amputated down to the first joint.
An employee was asked by a table saw's control panel operator to push back stacked material to be cut through the hold-down bar area. The injured employee hit the E-stop button to push back the material as requested. While his hand was still on the material, the control panel operator hit the cut buttons, causing the hold-down bar to come down on the injured employee's right hand. The employee pulled his right hand out from under the hold-down bar, resulting in an amputation of the right index finger up to the knuckle with bone loss.
An employee was working to build an electrical substation. He was cleaning out the inside of a fixed section of a PVC pipe on the end that was furthest from an excavator. The excavator was outside of the trench and more than 25 feet away when it moved a pipe, pinching the employee's right arm between the two pipes. The employee's forearm was fractured.
An employee was anchored to a movable piece of equipment called a "lid" with a self-retracting lifeline harness. An overhead crane lifted the equipment, causing the employee to be pulled by his harness. The employee was pulled off the walkway and swung over the wall of the kiln. His body and head struck the wall. The employee lost consciousness and sustained a laceration to the side of his head that required stitches. The employee also sustained multiple fractured ribs and fractured vertebrae.
An employee was in a scissor lift, preparing to strip formwork from the underside of a concrete deck. As the lift was ascending, the employee's left little finger was pinched between the lift rail and the concrete beam above. The employee was hospitalized, and the soft tissue of their left little fingertip was amputated; the finger's bony tuft was also damaged.
An employee was operating an order picker when his left middle finger was crushed between the lift and storage racking. The employee's fingertip was amputated.
An employee was ascending in a scissor lift when his left thumb was caught between between the railing of the lift and a piece of equipment installed in the ceiling. The employee's thumb tip was amputated.
More severe injuries in this industry (NAICS 326130)
The injured employee was letting air out of a winding shaft using scissors as a lift table was used to pull the roll off the shaft. The roll/cardboard core slid over the top of the injured employee's scissors and caused the scissors to amputate the employee's little fingertip at the nail base.
An employee was dropping off a skid of laminate to be cut at a table saw. The skid was lifted and the forks tilted forward when the stack slid forward and struck the injured employee. The employee was pinned between the laminate and the table of the saw, resulting in a back fracture and a laceration to the liver.
An employee was using a machine to cut a roll of plastic sheeting. The employee's right hand was at the end of the roll, and when the cutting mechanism of the machine cycled, the employee's right middle and ring fingers were cut, resulting in amputations to both fingers.
An employee was running acrylic film through an automated winding machine which wraps film around a cardboard cylinder core. He noticed that the film had slipped off the winder. He went to the front of the machine to re-attach the film to the winder spool. His fingers got caught between the film and the spool and his left arm was pulled up by the winder spool. The employee was hospitalized with a broken left forearm. Another employee injured their shoulder when pulling the first injured employee out of the machine.
After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.
An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.
An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.