Wilsonart LLC

An employee was dropping off a skid of laminate to be cut at a table saw. The skid was lifted and the forks tilted forward when the stack slid forward and struck the injured employee. The employee was pinned between the laminate and the table of the saw, resulting in a back fracture and a laceration to the liver.

The injured employee and a co-worker were loading a pallet of material onto a rack using a hydraulic lift system. The employee on the south side of the lift picked up the board about 2 inches so the board could enter the rack. The employee on the north side of the lift pressed the travel button to align the board with the rack opening. The injured employee was pinned between the lift and the rack and sustained fractured ribs.

An employee was standing on a 4-by-8 wooden pallet on the forks of a forklift, elevated to the second level of a rack. While pulling a cabinet off the shelf, the employee fell. He landed on the floor 7 or 8 feet below and suffered an injury to his heel.

An employee was pulling a kraft paper roll when a spindle crushed and amputated his right middle finger.

An employee was asked by a table saw's control panel operator to push back stacked material to be cut through the hold-down bar area. The injured employee hit the E-stop button to push back the material as requested. While his hand was still on the material, the control panel operator hit the cut buttons, causing the hold-down bar to come down on the injured employee's right hand. The employee pulled his right hand out from under the hold-down bar, resulting in an amputation of the right index finger up to the knuckle with bone loss.

Employees were assembling and testing a butterfly valve unit and actuator combo. When the unit was function tested with air, the valve gate closed on an employee's left thumb resulting in a fracture and laceration.

An employee was doing a daily inspection of the sifter screen on a mixer when the mixer line activated. The armature for the screen struck the employee's right wrist. Their wrist was cut and their hand was fractured.

An employee was being trained on a machine when a roller came down on their hand, resulting in a fracture and laceration.

An employee was doing a dry run during the setup of an ice cream machine. The machine indexed and the filler head amputated the employee's left middle finger above the last knuckle.

An employee was on a 3-foot ladder guiding cable onto a spool during installation on an overhead door. As the control box was jogged, the employee's hand was caught between the cable and spool, resulting in a wrist and hand fracture.

An employee was working with fiberglass and resins. The employee was hospitalized after having difficulty breathing caused due to chemical exposure.

The injured employee was letting air out of a winding shaft using scissors as a lift table was used to pull the roll off the shaft. The roll/cardboard core slid over the top of the injured employee's scissors and caused the scissors to amputate the employee's little fingertip at the nail base.

An employee was dropping off a skid of laminate to be cut at a table saw. The skid was lifted and the forks tilted forward when the stack slid forward and struck the injured employee. The employee was pinned between the laminate and the table of the saw, resulting in a back fracture and a laceration to the liver.

An employee was using a machine to cut a roll of plastic sheeting. The employee's right hand was at the end of the roll, and when the cutting mechanism of the machine cycled, the employee's right middle and ring fingers were cut, resulting in amputations to both fingers.

An employee was running acrylic film through an automated winding machine which wraps film around a cardboard cylinder core. He noticed that the film had slipped off the winder. He went to the front of the machine to re-attach the film to the winder spool. His fingers got caught between the film and the spool and his left arm was pulled up by the winder spool. The employee was hospitalized with a broken left forearm. Another employee injured their shoulder when pulling the first injured employee out of the machine.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.