Struck by dislodged or detached object(s) · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at GE Vernova Operations LLC, 71 Florida Ave, BANGOR, MAINE 04401
on — Fractures , affecting the Pelvis.
Final narrative
An employee was working with a dual flow steam diaphragm on a 500-pound lathe machine. A machine part came off the spindle, colliding with machine guarding doors and causing a door to come loose and fall outward from the machine. The door struck the employee, knocking them to the floor and pinning them from the waist down. The employee sustained a broken pelvis and was hospitalized.
Hospitalized Pelvis Exterior vehicle and machine parts unspecified
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
A service crew was pulling a pump and motor from a well. After breaking a joint of pipe loose from another joint, an employee grabbed the chain tongs to prevent the pipe from spinning in the well, so the crew could continue taking it apart. The bolt that attaches the chain to the handle of the chain tongs broke, causing the chain to swing around and strike the employee's lower right leg. The chain severely punctured his leg and fractured his tibia.
An employee was using a handheld grinder to cut a bolt. The grinding wheel broke apart and a fragment struck the employee s right hand, causing a laceration to the palm near the little finger.
An employee was operating a brake press when the top die broke, causing the bottom die to roll out and onto the employee's legs. Both of the employee's legs were crushed below the knee, and both legs were partially amputated. The employee's left leg was also fractured above the knee.
A pressurized aircraft nose landing gear strut assembly was being disassembled. The gland nut dislodged under pressure and made contact with an employee's left hand, breaking it.
More severe injuries in this industry (NAICS 333611)
Four employees were traveling in a utility task vehicle (UTV) on the east lot of the site. While turning, the UTV flipped over onto the driver's side. The driver's left wrist and hand were crushed by the frame of the UTV resulting in a fractured and dislocated wrist, as well as hand injuries. The driver was hospitalized and required surgery.
On August 15th, 2025, an employee was aligning/connecting a coupler to the generator of a wind turbine. The coupler was secured in place by a strap that was connected to the turbine's chain hoist and a bolt. While lining up the remaining holes, the coupler rotated while the employee's right index finger was in one of the bolt holes, causing a partial amputation through the phalanx.
Employees were preparing to unload a wind turbine gearbox from a flatbed trailer. An employee went to reposition himself on the flatbed trailer and grabbed onto a wooden piece of the shipping cribbing for support. The piece of wood began to come loose, causing the employee to lose his balance. The employee jumped to the ground about 4 feet below and landed on his feet. His left ankle rolled and the employee was hospitalized with a fractured ankle that required surgery.
An employee was working to move a paper roller carriage, which is a 3 by 3-foot paper roll weighing approximately 500 pounds. The employee's hands were positioned in the area where the spool meets the cradle. As the employee moved the carriage across a floor track, the paper roll was dislodged and caught the employee's finger, severing it. The employee's right middle fingertip was partially amputated.
A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.
Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.
An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.
An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.