Jarrett Bay Boatworks

Two employees were installing the port rudder into a 58-foot marine vessel. The vessel was suspended in the hoist straps of a marine travel lift. The employees were supporting the rudder vertically under the vessel when the lift dropped the stern of the vessel approximately 12 inches. The rudder became tightly wedged between the bottom of the vessel and the gravel ground. One of the employees had their fingers crushed between the rudder and the ground. The injured employee's left index finger was amputated and the left middle finger was severely injured, but remained attached.

An employee was operating a battery-powered broom to clean demolition debris off the top of the outermost bridge girder. The girder was approximately 11 feet above the demolition scaffold below. The employee fell approximately 8 feet to wind bracing below. The employee was hospitalized with a pelvis/tailbone fracture. Fall protection was in place at the time.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was cleaning out an inlet pipe in a stormwater structure. The employee stepped back, fell into the pipe, and landed on concrete 13 feet below, at the bottom of the structure. He suffered a broken back.

An employee was working on a platform, raised 6 to 8 feet in the air, to get something off a rack. The employee fell from the platform to the ground and sustained a head injury and injury to multiple body parts.

An employee was preparing to unjam an auger shaft while standing on a forklift-elevated, job-made platform. The employee's wrench slipped off the equipment, causing them to lose their balance and fall. The employee landed on the ground 14 feet below and suffered fractures to the orbital bone, left elbow, and lower back.

An employee was unbinding material that was caught in a horizontal band saw. The became unbound and it re-engaged while the employee was reaching for the blade. Two of the employee's fingers were amputated.

An employee was working on a ship in the sun when they began experiencing symptoms of heat exhaustion, resulting in hospitalization.

An employee was working in the hull of a boat, applying resin as part of lamination activities. He sat down and lost consciousness due to heat exhaustion. The employee was hospitalized.

An employee was operating a surfacing machine that used a rotating wire brush in a cabinet. A sheet of EVA foam material became stuck in the machine; as the employee was removing it, the wire brush contacted his left hand. He suffered a fracture and abrasions to the left arm.

An employee was operating a CNC machine. The employee lifted the guard and went to clean a part. The tooling was still rotating and caught the employee's glove, pulling it into the tooling and amputating their left ring finger.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was preparing hot melted butter on a flat-top grill and placing it in small containers once it was melted. As she turned to set the container down, it slipped out of her hand and landed on the grill. Butter splashed up and hit her in the face. The employee suffered second-degree burns to her right eye and the right side of her head and face, as well as first-degree burns to her right forearm.

An employee pulled into the customer's driveway, parked, and exited the vehicle. He opened the sliding side door on the vehicle to retrieve a package. The customer began backing their vehicle out of their garage and it struck the employee in the back of his left leg. He was pinned him between the two vehicles, causing contusions and lacerations.

An employee reached into a hamper, picked up a package, and was hospitalized with a back injury that caused pain in his lower extremities.

On July 10, 2025, an employee tripped over a yellow pillar and fell to the floor. The employee was hospitalized with a fractured left femur.