HME, Inc.

An employee was operating a beam rotator when the chain bumped a steel plate that was stacked on top of the flange. The plate fell off the beam and landed on the employee's left foot, resulting in a laceration.

An employee was manually moving material to finish fabrication. The angle rolled over the employee's finger, smashing it between the sawhorse and material. His fingertip was amputated.

A plate machine operator had his foot on/under the plate machine and the moving gantry on the machine caught his foot and drug it causing a chip fracture and lacerations.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

A service crew was pulling a pump and motor from a well. After breaking a joint of pipe loose from another joint, an employee grabbed the chain tongs to prevent the pipe from spinning in the well, so the crew could continue taking it apart. The bolt that attaches the chain to the handle of the chain tongs broke, causing the chain to swing around and strike the employee's lower right leg. The chain severely punctured his leg and fractured his tibia.

An employee was using a handheld grinder to cut a bolt. The grinding wheel broke apart and a fragment struck the employee s right hand, causing a laceration to the palm near the little finger.

An employee was operating a brake press when the top die broke, causing the bottom die to roll out and onto the employee's legs. Both of the employee's legs were crushed below the knee, and both legs were partially amputated. The employee's left leg was also fractured above the knee.

A pressurized aircraft nose landing gear strut assembly was being disassembled. The gland nut dislodged under pressure and made contact with an employee's left hand, breaking it.

On October 21, 2025, an employee was operating a saw when a pneumatic clamp caught their right middle finger. The employee suffered a partial amputation to the finger.

An employee completed an end cut on a metal shim and started transferring the metal shim from the saw conveyor to two saw horses in the area. The employee set one end of the shim (7 feet long x 8 inches wide, weighing 218 pounds) on one of the saw horses, then slid the other end onto the other saw horse and the shim fell from the first saw horse. The employee's left index fingertip was pinched between the saw horse and the shim, resulting in a skin avulsion. The fingertip was amputated later.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was moving steel beams with an overhead crane when the bundle struck a bollard and became unstable. As the employee reached to stop the material from shifting, his thumb was pinched in-between the beams, resulting in a partial amputation.

An employee was rigging a steel joist to be lifted by a crane. The joist fell and pinned the employee against the concrete ground. The employee sustained fractures to multiple ribs, his right arm, right tibia, and an open fracture to his right ankle, as well as a dislocated right hip.

An employee was working to remove a product blockage from a piece of equipment. The employee was struck by a metal bar near the deck of the pin mixer equipment and sustained blunt force trauma to the torso.

An employee was moving a rack onto a lower conveyor in the south heat treat area when their finger got caught between the part tray and the rollers, resulting in a fingertip fracture and amputation.

An employee was climbing a ladder to get on top of the breakroom. The ladder slipped, causing him to fall to the ground. The employee sustained fractures to his upper back, left foot, and ankle.

Two employees were removing a circuit breaker. The injured employee was using wrenches in the removal process. One of the wrenches contacted an adjacent door, resulting in an arc flash. The employee suffered burns to their neck, face, and ear, as well as momentary vision loss due to the flash.

An employee bent over to pick up a rubber mat from the ground. When he grabbed the corner of the mat, a rattlesnake hidden under it bit his left middle finger near the first knuckle. He was hospitalized.