Vorteq Coil Finishers, LLC

An employee was using a hand file to sand a part attached to the chuck on a powered lathe. Their right glove became caught and the employee's hand was pulled into the chuck, resulting in three finger amputations and an injury to the right ear. The employee was hospitalized.

An employee was walking back to the office when they tripped on a Christmas tree storage bag and fell to the floor. The employee sustained fractures to their clavicle and humerus.

On November 8, 2024, an employee was inspecting the aluminum material on the line for a defect. The employee stumbled and his face made contact with the moving material, resulting in a severe laceration to the right side of his face. The employee was hospitalized for surgery.

An employee was using an overhead trolley crane to lift an aluminum coil when the coil fell on the employee's leg, resulting in a fractured lower leg.

An employee was moving coils with a crane. When the crane set down a coil, its hook slipped out of the coil. The employee was pinned against another coil, suffered hip bruising, and was hospitalized.

An employee was inspecting a generator whose radiator was leaking. He slipped, and a fan blade in the generator amputated his thumb and index finger.

A temporary employee turned off a planer machine, opened the housing, and began clearing a jam. The machine's spinning blade caught his right hand and degloved the index finger.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was cutting steel channels from a hanging rack that was being supported by a forklift. When they were finished, the forklift started moving the rack out of the area and a piece of material snagged one of the rack legs, causing the rack to tilt backward. The rack slipped off the forklift and struck the employee on his right side/lower back. He sustained a fractured pelvis and was hospitalized.

An employee was working to remove waste wire between two boat rack/spreader bars (10 feet in length, 8 inches wide, and 16 inches tall, with a center lifting point for a crane hook) in the hanging department. One boat rack was leaning on another boat rack. The employee reached between the boat racks to move the leaning boat rack and remove the waste wire. The leaning boat rack shifted and the employee's left index finger was pinched between the two racks (weighing approximately 600 pounds each). The employee sustained an abrasive amputation of the left index fingertip from the nailbed up.

An employee was performing maintenance on a coating machine and the belt cover guard was removed to repair the belt. The moving belt caught the employee's fingers and pulled them between the belts, injuring three fingers on the employee's left hand. The fingernails were removed from their little and middle fingers. The ring finger was amputated at the first knuckle.

An employee tripped, fell to the floor, and suffered a broken right radius. The employee was hospitalized, requiring surgery.

An employee was stacking steel grating. The grating moved and their right ring finger got caught between grating. The last digit of the ring finger was amputated.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.