Arc Erecting, Inc.

An employee was turning on a machine and searching for the work order to begin operations. To access the board and items for the work orders, the employee lifted open the roller conveyor gate. As he released one side of the gate by pulling the latch, the weight increased on the other side where he had to push. This resulted in the gate snapping back and catching his left index finger, leading to partial amputation.

An employee was moving an air-supported wall structure when the sweeper got stuck. While lifting it up, it swung back into place and amputated his left middle fingertip.

Two employees were holding the wire of the swing to adjust its position while the swing was also being used by employees of another company. That resulted in sudden pressure on the wire, which pulled the clamp down, pinning one employee's right hand and another employee's lower left side under the clamp. One employee was hospitalized.

An employee was helping move a metal pipe for drilling. As the pipe was moved, it struck the employee in the right thigh, injuring it.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.