GULF STREAM MARINE Inc.

Two employees were discussing an operational assignment when a reversing forklift ran over the injured employee's right foot, resulting in a fractured right ankle.

The injured employee was removing a piece of 4" x 4" lumber from steel slab cargo in the yard area while another employee was operating a heavy-duty powered industrial truck (PIT) to lift a steel slab with magnets using a reach stacker. The lift was reversing with the cargo hoisted when the rear tire of the PIT hit a pothole and caused the slab to swing back and forth. As a result, the steel slab struck the injured employee in his abdominal area. The employee suffered a pelvic fracture, fractures to the L4 and L5 vertebrae, and a possible bladder contusion.

A load of cargo from a vessel was being landed on the dock. The injured employee walked towards the load in order to unhook the rigging, when one of the 4-ton round steel bars rolled and came to rest on his left foot. The employee was hospitalized with a fractured left ankle.

An employee was removing a chain binder that was used to secure cargo to a vessel. While working to free the handle of the tension binder from the deck plate using the handle of another binder, the binder suddenly released and struck the employee on the left side of his face and on the right thumb. The employee sustained a fractured right thumb and a laceration on the left cheek.

An employee was struck by a powered industrial truck while standing in an open area of the facility causing a laceration to the lower right leg.

An employee was preparing a barge for the end of a day's drilling operations. He was setting a spud on the barge when the spud struck him and broke his right leg.

A team of employees was moving boats from one slip in a marina to another using rope. An employee slipped while moving around in a boat and suffered a broken left femur.

The injured employee was standing by the controls for the electric spud system on the barge, preparing to raise the spuds. Meanwhile, an excavator was moving a mat on the deck. As the excavator swung from port to starboard, it's counterweight struck the injured employee s shoulder, causing them to lose balance and fall against the spud controls. The employee sustained bruises and contusions to their right shoulder and chest.

An employee was inserting dogbone links (4 feet 9 inches in length) into the slots between sectional barges to connect the barges. A dogbone link became stuck in the slot and needed to slide down approximately 1 foot to be seated. The employee went to lift the dogbone link up and adjust it when the link became free. A burr on the flange of the link snagged the employee's right glove. The link slid into a seated position and the employee's right middle finger was caught between the top surface of the barge and the top flange of the dogbone link. The finger was partially amputated at the midsection of the distal phalanx.

An employee was working to unload cargo from a ship. A steel coil contacted the employee's left leg. The lower leg was fractured.

While preparing to install a new spool piece for a vapor and spent sulfuric acid line, an employee was working to ensure there was no residual product or pressure in the line before removing the 6-inch hose. The valve was cracked, and some spent acid still in the line sprayed out. The employee was standing off to the side and at a distance, but was still contacted by the hot acid, resulting in corrosive and thermal burns to their upper torso and mid-thighs of both legs.

An employee was driving a utility tractor rig when it struck the rear trailer of another utility tractor rig, which was traveling in the opposite direction. The glancing impact caused damage to the cab, and he sustained a laceration on right side of his face, a cervical fracture, two fractured left ribs, and a pelvic fracture. The employee was hospitalized.

The injured employee was standing by the controls for the electric spud system on the barge, preparing to raise the spuds. Meanwhile, an excavator was moving a mat on the deck. As the excavator swung from port to starboard, it's counterweight struck the injured employee s shoulder, causing them to lose balance and fall against the spud controls. The employee sustained bruises and contusions to their right shoulder and chest.

An employee was standing on the outside edge of a hopper barge while watching a skid steer push ore for an excavator (with a clamshell bucket) to unload. The excavator was on a work barge. The bucket of the excavator struck the employee and caused a near-amputation of their right arm and fractures of the ulna and radius of the left arm. The right arm required surgery.

An employee was inspecting a conveyor to see why it was not running. The employee entered the the conveyor motor area, tripped on a piece of angle iron welded to the floor, and fell. The employee sustained a fractured orbital bone.

A driver was exiting his vehicle outside the plant gate when his foot slipped on the top step of the truck. He fell to the ground, landed on his left hip and elbow. The employee was hospitalized with a fractured hip/femur.

A security employee was responding to an urgent call from staff regarding a violent patient. The employee tripped and fell on the floor outside of the stairwell. The employee sustained a closed head injury, contusion of the cerebrum without loss of consciousness, and a closed fracture of the distal end of the right radius.

A security employee was holstering her firearm when the gun discharged a bullet into her right leg. The employee was hospitalized.

A temporary employee was testing an electrical starter motor. He was placing tape on the starter while the breaker was not engaged, but the starter sent an arc flash that burned his hands and stomach.

An employee was walking on a sidewalk and stubbed his toe on an elevated portion of concrete, causing him to trip and fall. The employee's right knee was dislocated.