Ramco Erectors, Inc.

An employee was standing near a pipe which was on top of wooden boards. A wooden board rolled off and the pipe struck the employee's left foot, resulting in four broken toes.

An employee was installing insulation to a new commercial building. The employee fell through a hole in the roof paneling to the concrete ground 25 feet below and suffered facial fractures, a broken left wrist, broken ribs on the left side of their body, and a punctured lung. The employee was not tied off at the time.

An employee was installing metal decking when he fell while trying to grab a piece of sheet metal that was elevated by a forklift. He fell approximately 15 feet to a dirt surface and was hospitalized with head and neck trauma.

The injured employee was assisting in the disassembly phase after a radar array had been lowered and secured. The crew began removing load bearing pins from an overhead crane to free the radome. A load bearing pin was stuck. The injured employee went to remove the pin manually as a second team member applied pressure from the opposite side. The pin unexpectedly released and struck the injured employee s right thumb, resulting in partial amputation of the distal phalanx including an open distal phalanx fracture and nail bed laceration.

An employee was shoveling excess material (spillage) that consisted of dry mix, sand, aggregate and cement. As he was shoveling, some material blew back in his face and around his safety glasses. He got a piece of metal in his left eye that required surgery. The employee was hospitalized.

An employee was feeding boards into an edger. They fed a board in and then adjusted the blade for a second board that was wider. When they fed the second board into the edger, it hit the first board and kicked back, striking the employee in the chest. They sustained injuries including a spine fracture, an injured pancreas, as well as potential injuries to their spleen, liver, and intestine. The employee was hospitalized and required surgery.

An employee was helping an operator to pull a cable off a winch. The operator pulled in the line when it hooked some tree brush. The brush then whipped around and struck the employee's arm, resulting in a broken arm.

A co-worker was adjusting an overhead bracket with an impact wrench when the tool flew out of their hand and struck the injured employee in the face. The injured employee sustained an injury to their left eye.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.