Federal OSHA recorded a severe workplace injury
at Varnum Enterprises LLC, 11 TROWBRIDGE DR, BETHEL, CONNECTICUT 06801
on — Thermal burns degree unspecified, affecting the Ears and facial region unspecified.
Final narrative
During the fabrication of a metal railing, an employee was heating a metal bar with an acetylene torch to prepare the bar for bending. After heating the bar, the acetylene torch was extinguished and placed in the open end of a 4 rectangular tube. Acetylene from the torch leaked into the tube. Several minutes later, the employee used a hand grinder that produced sparks which ignited the acetylene. The employee sustained facial burns.
Hospitalized Ears and facial region unspecified Other hydrocarbon gas
An employee was using a torch to loosen a bolt on a water trailer. Natural gas was present in the water and it ignited, causing a fire. The employee sustained third-degree burns to their upper leg.
An employee had been removing phosphorus pentasulfide while on a scaffold. He was using a non-sparking tool to dislodge the phosphoric material. The employee noticed a flash of flame. He descended the scaffold, but the flash ignited residual phosphorus pentasulfide that was on the outside of the employee's personal protective equipment (PPE). He sustained thermal burns to his right hand and right calf.
An employee was taking a butane gas sample as part of the hydrocarbon refining process. A component disconnected and the butane ignited, resulting in first- and second-degree burns to the employee's forearms and to their face, including their cheeks, chin, and neck.
An employee was troubleshooting a power washer in the field. Because there might have been water in its fuel, he brought it back to the shop and drained about a gallon of fuel from the tank into a plastic container. Some of the fuel spilled onto the floor and ignited. The employee was stomping out the fire when he lost his balance and tripped into a stool, which caused the plastic container to spill more fuel onto the fire. The employee's pants and shirt caught on fire, and he fell, abrading his knee while trying to get through the flames. As well as the knee abrasion, he suffered burns to the left leg and left lower quadrant of the torso. He was hospitalized.
An employee was fueling a gasoline-powered pressure washer with a safety fuel can. During the transfer the fuel ignited, causing a fire. The employee sustained burns to his nose, and his right hand and forearm.
More severe injuries in this industry (NAICS 337110)
An employee fell to an office floor, landing on her right side and suffering a broken hip, a broken right arm, and a concussion. She was hospitalized, requiring surgery.
An employee was clearing a small piece of wood that had jammed in the back of a machine. A cutting blade in the machine lacerated the employee's right forearm. The employee was hospitalized, requiring surgery.
An employee was operating a stand-up forklift to travel from the warehouse to the breakroom area. The forklift struck the breakroom wall, causing a fracture/crush injury to his left foot.
An employee was cutting a piece of wood with a table saw. The wood bound in the saw, which then pulled the employee's right hand into the blade. His middle finger was cut and fractured.
An employee was checking on a machine outside of the building and removed a cover to clean out a blocked area. His hand was caught by a rotary valve in a dust collection machine. The employee's fingertip was amputated.
An employee was working to clean a glue roller with a scraper tool. The tool and the employee's left thumb were pinched between two rollers, resulting in a partial amputation.
An employee was re-arranging boxes of pipe insulation on a pallet. One of the boxes fell from the pallet and knocked over an upright empty cylinder. The cylinder fell and crushed the tip of the employee's right toe. The employee's toe required surgical amputation.
An employee was securing the claw of a grapple truck to the truck bed. His left little finger was caught between the tie down strap and the rub rail of the truck, resulting in partial amputation of the finger.
An employee was cutting extruded aluminum framing material using a horizontal band saw. She went to grab a rag in the machine when the rag contacted the blade and pulled her hand in toward the blade, resulting in a partial amputation of the right index finger.