Sappi North America

The injured employee was training another employee, watching the second employee conduct a pump swap. The expansion joint fitting failed during the swap and caustic lime solution sprayed about 10-15 feet, hitting the injured employee. The employee suffered chemical burns to the leg, torso, and left eye and was hospitalized.

An employee was using a winding machine when his right middle finger was pinched and partially amputated between the machine's carriage and roller.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.

An employee was rigging I-beams. An I-beam slid off the stack of I-beams and fractured the employee's leg.

Tools and parts were being lowered to the ground from an elevated platform in a 5-gallon bucket. The rope being used to lower the bucket failed; the tools and parts fell and lacerated the left forearm and upper left leg of an employee on the ground.

An employee was tracking an infeed belt on a scrap hogger when their right arm was caught between the belt and a roller. The arm was broken and the employee's shoulder was dislocated. The employee was hospitalized.

An employee was working to clear a jam from a paper napkin folder. The ram that advanced the napkins pushed the employee's right arm into the side of the machine, causing several lacerations and a hairline fracture.

An employee was troubleshooting overflowing ink on a printer-slotter machine when their right ring fingertip was caught in a guarded roller, resulting in a partial amputation.

An employee was disconnecting wires in preparation to swap out a refiner motor when they contacted energized equipment and sustained an electrical shock. The employee was hospitalized.

A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.

Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.

An employee was using a metal shear when it amputated the tip of his right index finger.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.