OSCEOLA, ARKANSAS—
Big River Steel, LLC
Exposure to electric arc · Electrical burns any degree
At a glance
Federal OSHA recorded a severe workplace injury at Big River Steel, LLC, 2027 State Hwy 198, OSCEOLA, ARKANSAS 72370 on — Electrical burns any degree , affecting the Trunk and other lower extremities.
Final narrative
On June 22, 2025, an employee was performing scheduled maintenance at a ladle metallurgical furnace vault. As the employee was replacing a shear pin, they contacted an energized circuit, resulting in an arc flash. The employee sustained second-degree burns to their buttocks and both legs.
More severe injuries at Big River Steel, LLC
OSCEOLA, ARKANSAS—
Big River Steel, LLC
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
OSCEOLA, ARKANSAS—
Big River Steel, LLC
On September 1, 2024, an employee was clearing the metal material from the head of a bander as it was becoming misaligned. The gate was closed and it fell on the employee's right index finger, resulting in a fingertip amputation.
OSCEOLA, ARKANSAS—
Big River Steel, LLC
On June 25, 2024, at 4:00 PM, an employee was installing a new top on a scrap table when the top came down and pinched their left little finger, resulting in amputation of the finger at the first knuckle.
OSCEOLA, ARKANSAS—
Big River Steel, LLC
An employee was during utility work during the second shift, 7:00 p.m. to 7:00 a.m. At about 9:45 p.m., he began to feel hot and switched to light duty. At about 6:40 a.m., he felt ill and developed heat cramps. He was hospitalized, suffering from a heat-related illness.
OSCEOLA, ARKANSAS—
Big River Steel, LLC
Two employees were moving 12-inch-thick rolls of steel. While they were putting one of the rolls into place, it rolled back onto one employee's right hand, lacerating and breaking it.
View Big River Steel, LLC's full OSHA safety record →
Similar incidents · Same event type
HORSESHOE BAY, TEXAS—
Kasparian Underground LLC
An employee was terminating cables in a junction box. A loose ground wire came into contact with the bushing, causing a flash that burned the right side of the employee's face and his right hand.
LAKE PARK, FLORIDA—
Viking Utility Construction
An employee was using a bucket truck hoist to raise secondary aerial wiring. The wire made contact with the primary wire, causing an arc flash. The employee suffered burns to both hands and was hospitalized.
SHREVEPORT, LOUISIANA—
Jean Simpson Personnel Services, Inc.
A temporary employee was testing an electrical starter motor. He was placing tape on the starter while the breaker was not engaged, but the starter sent an arc flash that burned his hands and stomach.
MINNEOLA, KANSAS—
Vestas-American Wind Tech
Two employees were removing a circuit breaker. The injured employee was using wrenches in the removal process. One of the wrenches contacted an adjacent door, resulting in an arc flash. The employee suffered burns to their neck, face, and ear, as well as momentary vision loss due to the flash.
LAVONIA, GEORGIA—
Grief Brothers Corporation
An employee was installing a fuse in a machine cabinet. An arc flash burned the employee's left arm, and the employee was hospitalized.
More severe injuries in this industry (NAICS 331110)
LEVITTOWN, PENNSYLVANIA—
Floworks International LLC
An employee fell while entering the building. The employee was hospitalized with a fractured ankle and required surgery.
OSCEOLA, ARKANSAS—
Big River Steel, LLC
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
PEORIA, ILLINOIS—
Keystone Consolidated Industries, Inc.
An employee was working to close a furnace door. The hydraulic mechanism that opens and closes the furnace door was non-operational and had been disconnected to allow the furnace door to be opened manually. As the employee was releasing the pins that held the door open, the door and the hydraulic cylinder fell, pinching their left hand between the hydraulic cylinder's base plate and the furnace. The employee suffered amputation of the little fingertip.
SEGUIN, TEXAS—
Commercial Metals Company
A rolling mill was shut down due to a cobble between two mill stands. The injured employee was cleaning the cobble from the delivery side of stand A, while another employee went to the control panel to move stand B and stand A moved instead. The injured employee's right thumb got caught between the delivery guide of stand A and the looper trough. The tip of his thumb required surgical amputation to the bone to allow for stitches.
BEAVER DAM, WISCONSIN—
Metalcraft of Mayville, Inc.
An employee was helping another employee load stock material onto a press brake when the stock slipped. The injured employee's right index finger was caught between the press brake die and the stock, resulting in amputation at the first knuckle.
More severe injuries in ARKANSAS
BLYTHEVILLE, ARKANSAS—
NATIONAL MILL MAINTENANCE, LLC
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
TEXARKANA, ARKANSAS—
The Goodyear Tire & Rubber Company
On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.
OSCEOLA, ARKANSAS—
Big River Steel, LLC
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
PINE BLUFF, ARKANSAS—
American Tile & Marble Co., Inc
An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.
SCRANTON, ARKANSAS—
Johnson Industrial Coatings, LLC.
On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.