Metalplate Galvanizing, L.P.

The injured employee was helping a co-worker secure finishing material to a pallet using steel strapping (5/8" wide, 0.20" thick). The co-worker went to hand the strapping to the injured employee when they bent down and their right eye contacted the steel strapping, resulting in a laceration to the cornea and injury to the retina.

On November 25, 2024, an employee was leading the galvanizing crew. A finished galvanized beam was exiting the kettle when the support chain broke, causing molten zinc to splash the employee. The employee sustained burns to his chest and left forearm area.

An employee was moving solar beams (250-pound I-beams) from a stack using a specially designed tool to lower one beam at a time onto rollers. Once lowered onto rollers, the beam could then be navigated through the remainder of production. A beam was lowered onto his right-hand fingers and the employee sustained amputations of their distal middle and ring fingers.

An employee was working on a steel beam when it fell and struck them, breaking their right leg.

Employees were working in the finishing department preparing 180-pound steel frames for transport. A standing steel frame fell over onto the injured employee's left foot, resulting in bone exposure of the big toe. The toe was partially surgically amputated.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.

An employee was rigging I-beams. An I-beam slid off the stack of I-beams and fractured the employee's leg.

An employee was cutting steel channels from a hanging rack that was being supported by a forklift. When they were finished, the forklift started moving the rack out of the area and a piece of material snagged one of the rack legs, causing the rack to tilt backward. The rack slipped off the forklift and struck the employee on his right side/lower back. He sustained a fractured pelvis and was hospitalized.

An employee was working to remove waste wire between two boat rack/spreader bars (10 feet in length, 8 inches wide, and 16 inches tall, with a center lifting point for a crane hook) in the hanging department. One boat rack was leaning on another boat rack. The employee reached between the boat racks to move the leaning boat rack and remove the waste wire. The leaning boat rack shifted and the employee's left index finger was pinched between the two racks (weighing approximately 600 pounds each). The employee sustained an abrasive amputation of the left index fingertip from the nailbed up.

An employee was performing maintenance on a coating machine and the belt cover guard was removed to repair the belt. The moving belt caught the employee's fingers and pulled them between the belts, injuring three fingers on the employee's left hand. The fingernails were removed from their little and middle fingers. The ring finger was amputated at the first knuckle.

An employee tripped, fell to the floor, and suffered a broken right radius. The employee was hospitalized, requiring surgery.

An employee was stacking steel grating. The grating moved and their right ring finger got caught between grating. The last digit of the ring finger was amputated.

An employee was helping a coworker transport a tall palm tree with a mini skid steer. The employee was severely shocked by a high-voltage electrical wire above the ground.

An employee was retrieving a Christmas tree from a shelf using a ladder. He missed a step and fell to the concrete floor. He sustained injury to his head and wrist.

An employee was inspecting a generator whose radiator was leaking. He slipped, and a fan blade in the generator amputated his thumb and index finger.

An employee was operating an agricultural tractor during sugarcane harvesting. The employee sustained a lumbar sprain due to vibration or motion from the tractor.

An employee was moving a 3-ton condensing unit, strapped down on a dolly, out of a garage. The strap broke, causing the employee to fall backward onto the brick pavered driveway. The employee suffered injury to a spinal ligament in the neck.