NIBCO INC.

An employee was performing a machine set-up and had installed one set of holding jaws. His right index finger became caught in an air vise while re-clamping a part. The employee sustained a partial amputation above the fingernail.

A packing associate was cleaning under a packing bin and as he stood back up he grabbed the discharge chute. The discharge chute came down, pinching his finger at the hinge point, causing a partial amputation of his right thumb tip.

A temporary employee was pouring hot metal at a foundry when he began suffering from cramps. He left work and was hospitalized for dehydration.

An employee was removing a mold from the injection molding machine and pinched a finger resulting in amputation.

An employee was changing the jaws on a CNC lathe when the jaw hydraulic clamps were actuated by the foot control. His right index fingertip was amputated above the first joint between the jaws and the new part.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee's right middle finger was caught in a nip point. The employee suffered an amputation to the middle finger at the first knuckle.

An employee's left arm was caught in the fingers or jaws of the head stretcher machine, resulting in a laceration. The employee was hospitalized.

Two employees were setting up a mandrel in the spindle of a machine. The mandrel was side-shifted while an employee's hand was on the mast of a powered industrial truck. The employee suffered crushing injuries that resulted in amputations to the middle and ring fingertips.

An employee was working to remove a product blockage from a piece of equipment. The employee was struck by a metal bar near the deck of the pin mixer equipment and sustained blunt force trauma to the torso.

An employee was realigning two halves of a core box on a core-making machine. Pneumatic pressure released, causing the core box to close on the employee's right thumb. The thumb tip was amputated between the nail and the knuckle.

An employee was performing maintenance/electrical work inside a substation, and used a ladder to access the top of a panel box. The employee fell 8-9 feet from the top of the panel box to the ground. The employee was hospitalized with fractures to their ribs and a shoulder injury.

An employee noticed a block was out of place under the weighted mold frame. The employee used another block to push the block out and replace it. When the block came out, the frame came down on his right ring and little fingers. The employee sustained a fracture and partial amputation to the ring fingertip.

An employee was using a fork truck to move a tub containing molten iron that had been drained from the cupula. The tub tipped over and the molten metal came in contact with water. This caused the molten iron to splash back and burn the employee's upper torso.

An employee was attempting to transfer an iron pipe from the threader machine using a crane. When the employee grabbed ahold of straps used to move the iron pipe and pushed down on the strap, their left hand was caught between the strap and the iron pipe. The employee sustained an injury to the fingers of the hand that required surgery and hospitalization.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.