Kopco, Inc

An employee was unloading a shaft from a routing machine when the shaft disconnected from the magnet apparatus and struck the employee's right forearm and fractured it.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.

An employee was rigging I-beams. An I-beam slid off the stack of I-beams and fractured the employee's leg.

An employee was positioning dunnage on a trailer while pipe was unloaded from a forklift. A pipe fell and the employee's right thumb and index finger were caught between the pipe and a piece of dunnage. The thumb was crushed, and the index fingertip was amputated.

An employee was using a lifting sling on a crane to move a straight-bar bundle and place it on top of an existing bundle. When moving the lifting sling, it became pinched between the bundle and a wood cleat. The bundle then fell onto the employee's left foot, resulting in crush injuries.

An employee was setting up a flexible gear coupling hub in a lathe, preparing to bore it out to fit a shaft. The hub assembly was not secured in the chuck when the crane support was removed, and the employee's right little finger was caught between the hub assembly and the inside of the lathe. The fingertip was amputated.

An employee was using a crowbar to loosen a flat bar when the crowbar struck the employee's right eye. The employee was hospitalized and required surgery.

An employee was assisting another machinist with removing a finished part from a lathe. A crane equipped with a nylon sling was being used to lift the ~2,600-pound part from the lathe and move it onto a pallet. While the part was being set down on the pallet, the sling shifted, causing the employee s left middle finger to be pinched between the part and the sling. The employee's finger was amputated to the first knuckle.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.