UPS Industrial Services, LLC

An employee of UPS Industrial Services, LLC, was helping offload 40-foot sections of 8-inch pipe (weighing 3,000 pounds each) from a forklift in the laydown yard. As he reached to remove a piece of dunnage from the forklift tines, a pipe began to roll toward him from the back of the forklift mast toward the front. The pipe then fell from the forklift forks, catching his left and right legs against another pipe on the ground. He suffered fractures to both lower legs and was hospitalized, requiring surgery.

An employee was removing wooden crate panels. A panel from a different crate located behind the employee broke loose from its screws and struck the employee on the left hip area. The employee was hospitalized for a dislocated hip.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was moving a tensile strength test device with a dolly. The device fell from the dolly onto the employee's right leg, causing a compound fracture.

An employee was rigging I-beams. An I-beam slid off the stack of I-beams and fractured the employee's leg.

An employee was using a lifting sling on a crane to move a straight-bar bundle and place it on top of an existing bundle. When moving the lifting sling, it became pinched between the bundle and a wood cleat. The bundle then fell onto the employee's left foot, resulting in crush injuries.

An employee was stacking metal tubes using a forklift. A stack became unstable and the employee got out of the forklift to steady it, instructing his helper to get into the forklift. The forklift movement caused some tubes to fall and strike the employee, resulting in an open fracture of his left hand.

An employee was setting up a flexible gear coupling hub in a lathe, preparing to bore it out to fit a shaft. The hub assembly was not secured in the chuck when the crane support was removed, and the employee's right little finger was caught between the hub assembly and the inside of the lathe. The fingertip was amputated.

An employee was using a crowbar to loosen a flat bar when the crowbar struck the employee's right eye. The employee was hospitalized and required surgery.

An employee was assisting another machinist with removing a finished part from a lathe. A crane equipped with a nylon sling was being used to lift the ~2,600-pound part from the lathe and move it onto a pallet. While the part was being set down on the pallet, the sling shifted, causing the employee s left middle finger to be pinched between the part and the sling. The employee's finger was amputated to the first knuckle.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.