Caught or wedged between objects nonrunning · Amputations, avulsions, enucleations unspecified
At a glance
Federal OSHA recorded a severe workplace injury
at Sherwood Construction Company, Inc., NB US-75 to EB I-44 - Exit 231, TULSA, OKLAHOMA 74107
on — Amputations, avulsions, enucleations unspecified, affecting the Finger or thumb tip(s), nail(s).
Final narrative
Two employees were preparing 10-foot angle iron pieces (galvanized steel) to be placed on top of bridge beam edges. The north end of the angle iron dislodged and fell, which caused the south end of the angle iron to twist and pinch an employee's right middle fingertip against the beam edge. The employee's fingertip was amputated.
Amputation Finger or thumb tip(s), nail(s) Beams and rails metal
More severe injuries at Sherwood Construction Company, Inc.
An employee working on a highway bridge went to have a discussion with a nearby landowner, when he was chased by a dog and slipped or tripped down a slope. He was found on the ground with broken ribs.
Two employees were using gasoline and bar oil to ignite a brush pile when a flash fire occurred. An employee sustained burns to their face, arms, and hands.
An employee was changing a die in a press when the die slipped and crushed the employee's left index finger. The employee sustained an open facture of the tuft of the left distal phalanx and a partial amputation.
An employee was diagnosing the lack of flow of product to a powder bin. The employee removed the rotary star valve below the bin. While he was reinstalling the valve, his right middle finger was crushed between its shaft and its housing. The finger was partially amputated.
On October 30, 2025, an employee was working to adjust a stackable metal shipping container. As the container dropped into place, it caught the employee's hands in an area between the upper and lower cross-members. The employee suffered a laceration to the left ring finger that required stitches, bruising to the right ring finger, and fractures to the right middle finger that necessitated medical amputation of the fingertip.
An employee was changing the spacing on a telehandler's forks. A fork slipped, and the employee's left index finger was caught between it and the mast. The fingertip was medically amputated at the first knuckle.
An employee was conducting routine maintenance on a mixer. New lid pins had been installed, and the employee was rotating by hand to ensure they had been installed correctly. The employee's left middle finger was caught between the lid and top of a pin. The momentum from the mixer continued, causing a crushing injury to the finger. The employee underwent a medical amputation from the top knuckle to the tip of the finger.
More severe injuries in this industry (NAICS 237310)
An employee was operating a battery-powered broom to clean demolition debris off the top of the outermost bridge girder. The girder was approximately 11 feet above the demolition scaffold below. The employee fell approximately 8 feet to wind bracing below. The employee was hospitalized with a pelvis/tailbone fracture. Fall protection was in place at the time.
An employee was cleaning out an inlet pipe in a stormwater structure. The employee stepped back, fell into the pipe, and landed on concrete 13 feet below, at the bottom of the structure. He suffered a broken back.
A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.
An employee was operating a roller and paving a small pathway next to a pavilion. The ground was on a slight pitch, causing him to reach up toward the roll cage to stabilize himself. His right fifth finger was pinched between the roll cage and the rafter of the pavilion. The employee sustained a partial degloving injury with partial traumatic amputation.
An employee was working with paving equipment and heard a noise on the opposite side of the machine he was working on. When the machine stopped, the employee went to the opposite side and crouched down to investigate the noise. A mini track loader backed up and drove over the employee's leg. The employee sustained fractures to their lower leg, ankle, and foot.
An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.
An employee was working in the food service warehouse when he experienced chest pain, difficulty breathing, and lost consciousness. The employee sustained carbon monoxide poisoning.
An employee was cutting a piece of metal rod with a metal cutting machine. His right middle finger became caught between the rod and the machine's table. The employee's fingertip was partially amputated.
An employee was working at her desk. She went to stand up and fell to the floor beside the desk. The employee sustained a hip displacement and required surgery.
An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.