Other fall to lower level less than 6 feet · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at Triangle Engineering of Arkansas, Inc., 1101 N Redmond Rd, JACKSONVILLE, ARKANSAS 72076
on — Fractures, affecting the multiple body parts, n.e.c..
Final narrative
An employee was elevated between 5-7 ft. in a 4' w x 5' l x 3' tall wire basket attached to the forks of a sit-down rider forklift. The forklift operator began lowering the basket. The basket tilted and the employee fell out. The employee sustained a broken elbow and arm and a cracked pelvis. No fall protection was used.
HospitalizedMultiple body parts, n.e.c.Forklift, order picker, platform truck-powered
More severe injuries at Triangle Engineering of Arkansas, Inc.
An employee was standing and building HV fans by hand. He was bolting parts onto the fan with a wrench. Around 9 a.m., he started throwing up and felt ill. He was hospitalized due to possible heat stress.
The employee was working in the assembly line on the day of the incident. The employee notified his immediate supervisor that his hands were cramping. The employee was drinking water throughout the time that he was working, but the cramps began to get worse and he notified his supervisor. The employee was admitted to the hospital for dehydration and renal failure.
An employee was climbing a step ladder while carrying a 3-foot piece of conduit. As he went to reposition his feet on the ladder by pivoting, he slipped and fell from the third rung of a 6-foot ladder. The employee sustained fractures to the left femur, right elbow, and right ring finger.
An employee was descending a 4-step maintenance stand when she missed the bottom step and fell to the hangar floor. The employee suffered a left hip fracture.
An employee stopped a belt and was going to check it for missing packages. She fell backward 3-4 feet from an elevated platform and sustained a broken right arm.
An employee had just finished a routine concrete pour and was ascending the ladder to clean the concrete mixer truck. The employee lost their grip and fell approximately 2-3 feet, contacting the truck's bumper. The employee suffered rib fractures and a punctured lung.
An employee was performing duties as an expeditor. After opening the dock door, the employee scanned the barcode on the door of the truck and placed one foot on the truck and one foot on the dock. The truck drove out of the stall, causing the employee to fall 4 feet off the dock onto the concrete. The employee sustained fractures to the right side of the pelvis, elbow, and a left ring fingertip as well as injuries to the right wrist and bruising to the back and stomach.
More severe injuries in this industry (NAICS 333412)
An employee was at the brake press when the press was activated, causing the ram to move. Two fingertips on his right hand were crushed between the dies and partially amputated.
An employee was loading a piece of round aluminum into a CNC auto-spinning machine. Their left thumb was crushed between the tail block, the aluminum part, and the mandrel. The distal tip of the thumb was amputated.
An employee was seated at a press brake and was putting strips of steel (2-inches by 2-feet) into a brake press machine. The machine actuated and his right ring finger was crushed between the upper die and the steel material. The finger was amputated through the base of the nailbed.
An employee was using a manual spinning machine to cut out the center of an inlet. The cutter bar struck his neck and jaw, breaking the jaw and injuring an artery in his neck.
An employee was climbing a fence in pursuit of two people who had been trying to break into a facility. He fell from the fence, suffered a broken left leg, and was hospitalized.
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.