Compressed or pinched by shifting objects or equipment · Amputations
At a glance
Federal OSHA recorded a severe workplace injury
at Puget Sound Naval Shipyard, Dry Dock 1, BREMERTON, WASHINGTON 98314
on — Amputations, affecting the finger(s), fingernail(s), n.e.c..
Final narrative
An employee was training a junior employee. They were troubleshooting an electrical exhaust fan. The system was locked out at the time. The employee began manually rotating the pulley via the fan belt. As the employee pulled the belt, he drove his left hand between the belt he was pulling and the pulley. This crushed his left-hand ring fingertip, including the tip of the fourth distal. He sustained an amputation of the fourth distal, from the nailbed to the fingertip.
An employee was opening a scuttle on the third deck of an aircraft carrier. The scuttle quickly opened and pinched the employee's finger against a scaffold, resulting in a finger laceration and fractures.
An employee was working near a drive shaft on a naval vessel. He ducked under the propulsion shaft and his hard hat struck the shaft causing a broken vertebra in his neck. He was hospitalized.
An employee was operating a forklift and unloading a truck. After the truck was unloaded, the employee got off the forklift and proceeded to adjust the dock plate with a hook tool. The dock plate slipped and the employee went to adjust the plate with their hand when their left middle finger got caught. Their finger was amputated above the first joint.
An employee was rotating a carbide granulator blade when his finger was caught between the blade and a stationary part of the machine. The employee's right middle finger was partially amputated and they suffered an avulsion to the right ring fingertip.
An employee was using a CNC metal lathe machine in manual mode to check that the thread blocking tool made contact with the jaws. As the employee was manually spinning the spindle, his index fingertip was crushed between the spindle's jaws and the grooving insert, resulting in a fingertip amputation.
During a material handling operation, an employee's fingertip was caught under an air conditioning unit as the unit was lowered onto a cart. The employee's fingertip was amputated.
An employee was removing a bolt from a tractor hub when their right index finger was caught between the hub and the frame. The employee's fingertip was crushed and the employee was hospitalized.
More severe injuries in this industry (NAICS 336611)
An employee was hooking up bundled tie-downs with a chain. While he was holding a hook, the other hook was unlocked. This caused the employee's hook to slide down and pinch his right index finger between the chain and the shackle. He suffered an amputation to the fingertip (without bone loss), as well as an open fracture.
An employee was preparing to bend a flat bar in a brake press. When the machine was jogged, the stock rotated up and crushed his left middle fingertip against the outer frame of the die. The fingertip was amputated.
An employee was cutting metal with a torch. A piece of metal struck the employee's left foot, causing multiple fractures to metatarsal(s). The employee was hospitalized.
An employee was descending a ladder carrying a bag of trash. He fell, landed on the ground about 10 feet below, and suffered fractures to his right hip and pelvis.
An employee was drilling a hole into the sealed hold of a vessel so a marine chemist could test its atmosphere. Upon drilling the hole, a gas that was under pressure was released and caught fire at the drill motor, where the employee was holding it. The employee was burned.
An employee was performing restoration activities outside a 45-gallon condensation tank of a boiler system. As they were performing post-maintenance activities after repairing one of the two discharge pumps, one of the discharge valves would not open. The employee closed the intake pump to cool off the system and open the discharge valve. Two employees opened the inlet valve to return the tank to service. After they cracked open the inlet valve, a side wall of the tank blew out, causing the injured employee to suffer steam burns to half their body.
An employee was testing and troubleshooting the gang cylinder valve located in the gang area of the sawmill. The employee's fingertip was amputated by the gang cylinder valve.
An employee was unlocking containers on deck. The employee was de-lashing while standing on the edge of the lid. The lashing bar he was holding came off the cone, causing him to turn 90 degrees and strike a railing behind him. The employee sustained four fractured ribs.
An employee parked a side-by-side on the fixed internal ramp aboard a cargo ship. They exited the side-by-side and went to inspect the cargo below. The side-by-side rolled toward the employee and struck them as they were walking toward the edge of the ramp. The employee was knocked off the ramp and landed on the lower deck approximately 8 feet below. The employee was hospitalized with a fractured shoulder.