CRYSTAL FINISHING SYSTEMS INC

On May 8, 2024, at approximately 2:30 AM, two team members were retrieving a plate that popped out of the head puller/stretcher of an extrusion press and were putting it back into place using a crowbar and a small piece of aluminum. When the plate shifted back into place, the injured employee's right index finger was pinched under the plate and amputated.

An employee was walking when she tripped over a basket sensor and reached for a nearby chain-link fence to brace herself. The employee's right middle finger became caught on the fencing causing an amputation to the finger that resulted in hospitalization and surgery.

An employee was working in the extrusion department helping another employee remove a stuck ball of aluminum from the rollers of the roll-out table. The hot aluminum ball fell from the table and pinned the employee's leg against the table, resulting in second-and-third-degree burns to the employee's thigh and stomach.

An aluminum extrusion became stuck while it was being pulled out onto the table from a press. While trying to free it, an employee was struck by the puller as it retracted back home to the press area. The employee suffered a broken rib, a punctured lung, and abrasions. The machine was not locked out/tagged out at the time.

An employee was a passenger in a golf cart when he fell out of the golf cart as it turned to enter the facility. He tried to gain his footing but fell backwards onto the concrete, hitting his head on the pavement. He suffered a skull fracture and subdermal hematoma.

An employee was unloading a trailer when a box fell and struck the employee in the face. The employee suffered a concussion and was hospitalized.

An employee had been cutting lumber for a shed wall. A load of 16-foot trim pieces fell onto the employee causing vertebrae and ankle fractures.

An employee was unloading 30-foot 2-inch barrels from a pan holding about 20 barrels. The barrels tipped over, striking and breaking both of the employee's lower legs.

An employee was in a sandblasting area, preparing the surface of a plate heat exchanger frame for painting. The frame fell on the employee, who suffered fractures to vertebrae, the neck, pelvis, and rib cage; and punctured lungs.

An employee was installing doors when one of the doors fell on him, fracturing his lower leg. The employee was hospitalized.

An employee was cutting steel channels from a hanging rack that was being supported by a forklift. When they were finished, the forklift started moving the rack out of the area and a piece of material snagged one of the rack legs, causing the rack to tilt backward. The rack slipped off the forklift and struck the employee on his right side/lower back. He sustained a fractured pelvis and was hospitalized.

An employee was working to remove waste wire between two boat rack/spreader bars (10 feet in length, 8 inches wide, and 16 inches tall, with a center lifting point for a crane hook) in the hanging department. One boat rack was leaning on another boat rack. The employee reached between the boat racks to move the leaning boat rack and remove the waste wire. The leaning boat rack shifted and the employee's left index finger was pinched between the two racks (weighing approximately 600 pounds each). The employee sustained an abrasive amputation of the left index fingertip from the nailbed up.

An employee was performing maintenance on a coating machine and the belt cover guard was removed to repair the belt. The moving belt caught the employee's fingers and pulled them between the belts, injuring three fingers on the employee's left hand. The fingernails were removed from their little and middle fingers. The ring finger was amputated at the first knuckle.

An employee tripped, fell to the floor, and suffered a broken right radius. The employee was hospitalized, requiring surgery.

An employee was stacking steel grating. The grating moved and their right ring finger got caught between grating. The last digit of the ring finger was amputated.

The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.

An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.

A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.

An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.

An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.