Xtreme Drilling and Coil Services

An employee was walking near a forklift holding a non-secure joint casing. The employee sustained a compound fracture to the leg when the joint casing rolled off the forklift tines and landed on the employee's leg.

On April 6, 2015, an employee working on a rig sustained a head injury that required stitches after falling approximately 5.5 feet from the top of the scavenger tank/platform to the matting board. Guardrails on top of the platform were removed at the time. The employee was hospitalized overnight.

On November 9, 2023, an employee was removing plywood from the west face of a basement level buck hoist to prepare to dismantle one of the cabs. When the employee pulled on the plywood, it fell and pulled a rope that partially amputated the employee's thumb.

An employee was holding a rigging line and assisting in the removal of an old light pole from its base. When the load was lifted by a forklift, it shifted. The tag line lifted the employee off the ground and propelled him through the air. The employee landed on the ground and sustained back fractures.

An employee was performing maintenance on a bucket truck when his right hand became caught in some rope, causing amputations to three fingers down to the first knuckle.

An employee was conducting a fall rescue demonstration. A 165-pound demonstration dummy was released from a height, putting tension on the lanyard. The employee's left hand, little finger, and thumb were caught in the wire rope lanyard, resulting in a medical amputation of the left little finger as well as lacerations to the left thumb.

An employee was using a crank and cable to lower a light tower due to windy conditions. The light shaft became hung up and released the tension in the cable, which wrapped around the employee's left hand, resulting in amputations of three fingers.

An employee was stepping down off a 6-inch containment platform to finish loading his truck, when his right ankle rolled. The employee sustained a fractured tibia and fibula at the right ankle and required surgery.

A service crew was pulling a pump and motor from a well. After breaking a joint of pipe loose from another joint, an employee grabbed the chain tongs to prevent the pipe from spinning in the well, so the crew could continue taking it apart. The bolt that attaches the chain to the handle of the chain tongs broke, causing the chain to swing around and strike the employee's lower right leg. The chain severely punctured his leg and fractured his tibia.

An employee was working to remove a stuck fish tool from a drill shoe. Their thumb was struck by a hammer, resulting in amputation.

An employee arrived on location and loaded a blow-out-preventer (BOP) on a 1-ton flatbed truck. While standing on the flatbed securing the the BOP, the employee stepped into a void/hole on the flatbed surface. This caused him to lose balance and fall off the truck bed with his leg still caught in the hole. As a result, he sustained fractures to his left leg.

An employee was rigging up a location. He was using an Allen wrench to free up rotation and start the drawworks engine manually. The engine rotated and his left little finger became caught between the Allen wrench and the engine. The employee sustained an amputation to his little finger and fractures to his wrist.

An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.

An employee was cutting cabinet trim using a table saw when four fingers on his left hand were severed, resulting in hospitalization and amputation.

An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.

A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.