Compressed or pinched by shifting objects or equipment · Amputations
At a glance
Federal OSHA recorded a severe workplace injury
at Blattner Energy, INC, 23987 CR 51, BURLINGTON, COLORADO 80807
on — Amputations, affecting the finger(s), fingernail(s), n.e.c..
Final narrative
On 7/17/15, an employee's thumb was amputated when caught between a large steel ring and a railing during loading of the steel ring onto a trailer.
An employee was repositioning a crane to a different location when the crane tipped over onto its side. The employee jumped off the crane 10-12 feet to the ground below, resulting in multiple fractured back vertebrae.
An employee was aligning the butt section of a wind turbine when his left middle finger was struck by the reaction arm when it extended, resulting in amputation to the first knuckle.
An employee was using a torquing tool to torque down bolts on the blades in a wind turbine. As he began to tighten a nut, his finger became caught between the torquing tool and the wall of the hub. The employee sustained an avulsion fracture to a finger.
An employee was removing bolts from a crane to disconnect the crane from a wind tower. When the crane was being lifted up, the employee's left hand caught on a bolt and was pulled into the bolt, resulting in an amputated thumb and ring finger.
An employee was operating a forklift and unloading a truck. After the truck was unloaded, the employee got off the forklift and proceeded to adjust the dock plate with a hook tool. The dock plate slipped and the employee went to adjust the plate with their hand when their left middle finger got caught. Their finger was amputated above the first joint.
An employee was rotating a carbide granulator blade when his finger was caught between the blade and a stationary part of the machine. The employee's right middle finger was partially amputated and they suffered an avulsion to the right ring fingertip.
An employee was using a CNC metal lathe machine in manual mode to check that the thread blocking tool made contact with the jaws. As the employee was manually spinning the spindle, his index fingertip was crushed between the spindle's jaws and the grooving insert, resulting in a fingertip amputation.
During a material handling operation, an employee's fingertip was caught under an air conditioning unit as the unit was lowered onto a cart. The employee's fingertip was amputated.
An employee was removing a bolt from a tractor hub when their right index finger was caught between the hub and the frame. The employee's fingertip was crushed and the employee was hospitalized.
More severe injuries in this industry (NAICS 221119)
Employees were preparing to replace a primary electrical cable. While two of the employees were working to remove the cable on one side of a switchgear, they came into contact with a wrench and the outside part of the switchgear. One employee suffered an electrical shock.
An employee was installing personal protective grounds at a substation when their hand contacted the end of the ground that was not energized, but induced voltage was created by wind and shocked them. This resulted in a burn on their thumb.
At about 9:35 a.m. on March 18, 2024, an employee was conducting maintenance on a non-operational fan controller in a switchgear room. The employee pulled the controller and began installing a new one. The employee was electrocuted, suffering third-degree burns to the right hand and fingers as well as burns to the right forearm, and was hospitalized.
An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.
An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.
A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.
An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.