Direct exposure to electricity, greater than 220 volts · Second degree electrical burns
At a glance
Federal OSHA recorded a severe workplace injury
at EAST BAY ELECTRIC, LLC, 13013 Willow Beach Rd, NORTH LITTLE ROCK, ARKANSAS 72117
on — Second degree electrical burns, affecting the multiple body parts, n.e.c..
Final narrative
An employee was working on a power line from a bucket truck moving wire lines from an old pole to set a new pole when the old cross arm braces broke and live electric wires fell on his right shoulder/arm. As a result of the two phased electrical contact flash, the employee suffered a second degree burn on the right shoulder and right side of his body and was hospitalized.
HospitalizedMultiple body parts, n.e.c.Power lines, transformers, convertors
On April 17, 2024, an employee was installing cross arms while in an aerial bucket truck when a 14,400-volt line became pinched between the bucket and a pole. The line was severed, causing an arc flash. The employee sustained second-degree burns to the left side of their body, arms, and face.
An employee was installing a ground wire to a power transmission pole. The ground wire contacted an energized portion of a cut-out, causing an arc-flash. The employee was hospitalized with second degree burns to their chest and arms.
An employee was connecting a utility transformer for underground service to a home. The employee's impact drill went across two connection bars with 240 volts of potential, creating an arc flash. The employee sustained burns to the face and eyes due to the arc flash and molten aluminum.
On December 15, 2023, at 9:15 AM, an employee was changing 60-amp fuses in a 480-volt panel when an arc flash occurred. The employee was hospitalized with burns to both hands.
An employee was troubleshooting the control setup for a variable air volume box above a ceiling. The employee's hand came into contact with an exposed, energized 277-volt wire that had loosened from its terminal on the box's assembly. He was shocked and fell off a ladder. His left hand passed across the ceiling grid and was lacerated. He also suffered an electrical burn to the right hand and was hospitalized.
An employee was moving a scissor lift through a doorway. The employee was pinned between the scissor lift and the doorframe, sustained a back injury, and was hospitalized.
An employee was standing on an A-frame ladder approximately 6 feet above the floor while he attached a suspended light fixture to the ceiling. The employee lost balance, and fell to the tiled floor below, sustaining blunt force trauma to his head.
An employee was inspecting the overhead area of a single-person lift and repositioning the lift through a double doorway. As they were transitioning through the doorway, they were caught between the doorframe and the vertical mast of the lift. The employee was hospitalized with injuries to the nose, left maxillary sinus, left orbital bone, and left jaw, with fractures at the maxillary sinus area.
The injured employee was performing routine maintenance on a fan belt/pulley. The injured employee and another person were moving the pulley back and forth manually to find a bearing issue. The injured employee's left ring finger got caught between the belt and the pulley wheel, resulting in a soft tissue amputation.
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.