G2 Secure Staff, LLC

An employee was performing lavatory servicing work for an aircraft. A fuel truck struck the employee, who suffered a compound fracture of the left femur.

An employee was trying to enter an aft cargo pit on an aircraft using an aircraft chock to gain more height. He tried to jump into the pit but did not succeed; his legs then swung under the fuselage and he fell backward, landing on his back on top of the chock and the ramp. He suffered a partially collapsed lung and two broken ribs.

An employee was helping to relocate a cart when their arm became caught between the cart and a concrete column, resulting in a broken bone in the right forearm.

An employee was operating a powered industrial truck inside a trailer. His finger was caught between the exterior frame of the truck and the inside wall of the trailer.

An employee suffered a left middle fingertip amputation while disconnecting a cart from an aircraft that was being serviced. He was hospitalized.

An employee was assisting with pipe on a drilling rig. The slips came down and landed on the employee's left foot fracturing four metatarsals.

Two employees were struck by the rotary table of a drilling rig while installing caisson. Employee 1 suffered multiple fractures, internal injuries, and head trauma. Employee 2 suffered multiple fractures, internal injuries, spinal injury, and head trauma.

Employees were felling hazard trees. The injured employee was conducting 'bucking' operations to saw a tree from the road when the tree kicked-back, pinning him against the ground and fracturing his left femur. The employee was hospitalized and required surgery.

An employee was greasing tongs on a work-over rig. The tongs lacerated one of the employee's fingers.

An employee was chaining a vehicle when he had to change tools and the compressor. As the compressor was being charged, the employee stepped near the vehicle to make sure the compressor was attached. Then, he instructed a co-worker to lower the compressor. His right hand was on the compressor and under the chain, causing his ring finger to be crushed.

Two employees fell from an access bridge while entering an aircraft to perform maintenance. They landed on the ground about 20 feet below, where one of them lost consciousness. One employee sustained a fractured knee and another employee sustained a back strain/sprain. Both employees were hospitalized.

An employee experienced sharp pain in his lower torso area while loading baggage into the front cargo pit of an aircraft. The employee sustained a hernia.

The injured employee was assisting in the disassembly phase after a radar array had been lowered and secured. The crew began removing load bearing pins from an overhead crane to free the radome. A load bearing pin was stuck. The injured employee went to remove the pin manually as a second team member applied pressure from the opposite side. The pin unexpectedly released and struck the injured employee s right thumb, resulting in partial amputation of the distal phalanx including an open distal phalanx fracture and nail bed laceration.

On September 11, 2025, an employee was lowering a railing system on an aircraft fueling cart when his gloved right ring finger was caught in the folding railing system, resulting in a fingertip amputation that required hospitalization and surgical reattachment.

An employee was working at ground level when an aviation engine cylinder weighing 30 pounds fell from a seven-foot high shelf and struck the employee on the head. The employee suffered a fractured skull and was hospitalized.

An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.

An employee was working in the food service warehouse when he experienced chest pain, difficulty breathing, and lost consciousness. The employee sustained carbon monoxide poisoning.

An employee was cutting a piece of metal rod with a metal cutting machine. His right middle finger became caught between the rod and the machine's table. The employee's fingertip was partially amputated.

An employee was working at her desk. She went to stand up and fell to the floor beside the desk. The employee sustained a hip displacement and required surgery.

An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.