United Steel, Inc.

On September 18, 2023, an employee's foot was struck by approximately 2,000 pounds of steel. The employee's foot and toes were crushed and the employee was hospitalized.

An employee was walking on a steel beam when they fell 14-feet, resulting in multiple fractures to the head, back, and clavicle, as well as a collapsed lung.

An employee was using a knife to cut a hose on welding equipment to investigate a leak. The knife amputated one of his fingertips without bone loss.

An employee was preparing to cut pipes with a portable band saw. He undid the tie wire and leaned one end of a 20-foot long pipe on a removable rail. As he went to move the pipe, a different rail was knocked over. The rail fell onto the employee and struck his left leg, resulting in a left tibia/fibula fracture.

An employee was using a concrete mixer that was attached to a skid steer and amputated the tip of his right index finger.

An employee was moving a piece of an I-beam for welding when it rolled off the cribbing. The employee went to catch it when it fell and crushed the employee's finger, resulting in a partial amputation.

An employee was helping to disassemble large reels used to store steel wire when a 264-pound flange from the reel fell over onto the employee's left leg. The employee sustained multiple fractures to their leg and ligament injuries to the lower leg.

The injured employee was putting away materials on the warehouse floor as a co-worker was pushing a pallet onto a nearby shelf. The pallet knocked another pallet forward, causing it to fall onto the injured employee's shoulders. The employee suffered fractures in their right and left knees and ankles.

Employees were moving a single man lift into a building and reclining the lift to position it to fit through the door. The lift shifted and fell, causing the employee to sustain fractures to the left tibia and fibula. The employee was hospitalized and had surgery.

An employee was moving a light tower so it could be hitched to a truck. He grabbed the tongue of the trailer hitch on the light tower to slide it to the left. The tongue jack fell off, causing the light tower tongue to drop on the employee's right hand. The employee's middle fingertip was amputated.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

An employee was attempting to lift a steel beam from a horizontal, stacked position to a vertical position using a crane. They had placed two hooks on the east side of the beam on the flange. As the employee was hoisting the crane, the beam began to shift and pulled the employee forward onto the stack. When the material shifted, the hooks released and the material fell, pinning the employee between the two beams. The employee was hospitalized with soft tissue contusions on their proximal right thigh and interior left thigh.

An employee was standing on the surface of a steel beam about two feet wide. He slipped and fell backward, landing on the concrete ground about 20 feet below. The employee sustained a broken pelvis.

An employee was unloading a rebar delivery from a flatbed, 19-wheel trailer. The employee rigged the load with wire rope chokers. The load was picked up 3-4 feet above the trailer deck by a crane. The load began to swing and the employee grabbed onto it to prevent it from being pushed off the trailer deck. The crane continued to lift the load, and the employee let go so the crane did not lift him to the third story. The employee fell approximately 12 feet to the ground below, resulting in a back injury and fractured vertebrae.

An employee was attaching a steel angle plate weighing (approximately 200 pounds) to the end of a structural member (5,000 pounds) and was supported by dunnage. The dunnage was a crane mat (11 inches tall) with a 4x6 board on top of it and it supported five identical members. The main piece was 30.75 feet long, 37.25 feet tall, and 1 food wide. As the employee slid the piece of metal on top of the member to begin attaching it, the entire member began to tip over. The employee went to stop the main piece from tipping over and it landed on his ankle, fracturing it.

An employee was checking on a machine outside of the building and removed a cover to clean out a blocked area. His hand was caught by a rotary valve in a dust collection machine. The employee's fingertip was amputated.

An employee was working to clean a glue roller with a scraper tool. The tool and the employee's left thumb were pinched between two rollers, resulting in a partial amputation.

An employee was re-arranging boxes of pipe insulation on a pallet. One of the boxes fell from the pallet and knocked over an upright empty cylinder. The cylinder fell and crushed the tip of the employee's right toe. The employee's toe required surgical amputation.

An employee was securing the claw of a grapple truck to the truck bed. His left little finger was caught between the tie down strap and the rub rail of the truck, resulting in partial amputation of the finger.

An employee was cutting extruded aluminum framing material using a horizontal band saw. She went to grab a rag in the machine when the rag contacted the blade and pulled her hand in toward the blade, resulting in a partial amputation of the right index finger.