Explosion of nonpressurized vapors, gases, or liquids · Third or fourth degree heat (thermal) burns
At a glance
Federal OSHA recorded a severe workplace injury
at Tolman Construction, 35 miles WNW in T3 R11 WELS, MILLINOCKET, MAINE 04462
on — Third or fourth degree heat (thermal) burns, affecting the multiple body parts, n.e.c..
Watch Tolman Construction — freeGet an email when a new federal OSHA severe-injury report for Tolman Construction is published. One employer, no account, unsubscribe in one click.
Final narrative
An employee was transferring diesel fuel from the middle tank of a fuel truck to the forward tank using a barrel pump when a fire/explosion occurred. The fire/explosion threw the employee off the tanker to the ground and ignited his clothing, causing second and third degree burns to his body and arms.
HospitalizedMultiple body parts, n.e.c.Semi, tractor-trailer, tanker truck
An employee was lighting the pilot light on a water heater. Gas ignited, causing a flash fire and explosion at the residential property. The employee suffered burns to the head, neck, upper torso, and upper extremities.
An employee was preparing a reach in cooler (fry cooler) and charging the system with refrigerant (R290)with his gauges. When the employee removed the gauges from the liquid line service valve, the refrigerant immediately escaped, and the liquid refrigerant exploded due to an unknown ignition source. The employee was burned on the face, hands, abdomen and knees.
An employee was lighting a gas stove/pizza oven when an explosion occurred due to a natural gas buildup. The employee sustained first- and second-degree burns to the face, neck, arms, hands, and legs.
An employee was re-lighting a sulfur burner while another employee increased the pressure on the gas valve. A gas explosion occurred. The employee sustained second-and third-degree burns to their arm, hand, chest, abdomen, and neck.
More severe injuries in this industry (NAICS 237310)
An employee was operating a battery-powered broom to clean demolition debris off the top of the outermost bridge girder. The girder was approximately 11 feet above the demolition scaffold below. The employee fell approximately 8 feet to wind bracing below. The employee was hospitalized with a pelvis/tailbone fracture. Fall protection was in place at the time.
An employee was cleaning out an inlet pipe in a stormwater structure. The employee stepped back, fell into the pipe, and landed on concrete 13 feet below, at the bottom of the structure. He suffered a broken back.
A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.
An employee was operating a roller and paving a small pathway next to a pavilion. The ground was on a slight pitch, causing him to reach up toward the roll cage to stabilize himself. His right fifth finger was pinched between the roll cage and the rafter of the pavilion. The employee sustained a partial degloving injury with partial traumatic amputation.
An employee was working with paving equipment and heard a noise on the opposite side of the machine he was working on. When the machine stopped, the employee went to the opposite side and crouched down to investigate the noise. A mini track loader backed up and drove over the employee's leg. The employee sustained fractures to their lower leg, ankle, and foot.
A crew was installing drilled micropiles alongside an outdoor covered deck foundation. The injured employee was working the front of the drill when a loose section of casing dropped onto the tip of a rig wrench and pulled the wrench down to an embedded casing. The employee's left little finger was caught between the rig wrench and the embedded casing and was amputated above the top knuckle.
Two employees were working to change a tire on a mobile slasher saw. The slasher weighs around 2,000 pounds and is towed. Employee 2 was lifting the saw while the injured employee was placing a block of wood under the frame for support. The slasher then lowered onto the block and the injured employee's left thumb was crushed between the slasher frame and the wood block, leading to an amputation at the first knuckle.
An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.
An employee was standing on a step stool, removing the nuts and bolts from the frame of a solar panel that was being replaced. The employee's cheek made contact with a connector with damaged insulation. The employee was shocked, briefly lost consciousness, and fell to the ground, suffering an injury to the left shoulder.