Wright Tree Service, Inc.

On April 10, 2025, an employee was climbing a fixed ladder on a chip truck. He fell backward from the ladder, striking his head on the ground and suffering a brain bleed.

On October 3, 2024, an employee was using a chainsaw to trim trees. They were moving a limb when the chainsaw contacted their left forearm and lacerated it.

An employee was working as a spotter for a tree truck that was being parked near a tree. The employee was behind the truck when he was pinned between the truck and the tree. The employee sustained a lacerated liver.

A tree fell on an employee, resulting in a neck fracture and forehead laceration.

An employee was ascending a tree to trim the top off with a chainsaw. At a height of 20 feet, he clipped into the equipment holding line. He then fell from the tree and landed on a chainsaw on the ground. The employee sustained a broken femur.

A crew was working near an electrical pole. A co-worker was using a front-loader to grade a slope when the loader slid into a guy-wire and became tangled and stuck. The injured employee used a handheld grinder to cut the wire a few feet from the ground. The lower part of the wire fell to the ground, but the upper part of the wire fell toward the pole and contacted an energized part before the end landed in nearby bushes. The employee attempted to shake the bush to free the wire so it could fall back toward the pole. The wire popped up and contacted his hands, resulting in electrical entry burns to both hands and exit burns on both feet.

On November 18, 2023, two employees were using a 2x4 to lift a power line. The boom lift they were operating made contact with power lines and both employees sustained electrical shock injuries.

An employee was part of a crew that was servicing a power line. The employee was in a bucket truck when he contacted the 7,200-volt power line. The electricity entered through one hand and exited the other, causing several electrical burns. The employee was not wearing proper personal protective equipment at the time.

An employee was helping a crew set up a 45-foot pole between two other poles. It was being set up between two energized lines and the pole made contact with the A-phase. The employee was electrocuted and lost consciousness. The electricity also caused an entry wound in their left forearm and an exit wound in their left foot.

An employee was handling a 45-foot long rebar for installation on the third floor of a building at a 30-foot elevation. The rebar came into close proximity of a powerline situated 13 feet off the building. The employee sustained electrical burns to his hands from electric discharge, requiring hospitalization.

An employee was cleaning leaves with a backpack blower when he fell from a ladder, resulting in injuries to his head, neck, and back.

An employee was helping to set up a mulch blowing truck when they were struck by an oncoming vehicle. The employee was hospitalized with a fractured knee, a concussion, and a head laceration; they also received stitches on their arm.

An employee was rappelling down a tree. When he was most of the way down, he fell on the ground and suffered a broken pelvis.

An employee was using a table saw to cut a piece of wood when the saw cut his thumb, index, and middle fingers. His index finger was amputated and he was hospitalized.

An employee was mowing a residential lawn at a client's house. The mower slid on the land and tipped over onto him. The employee was hospitalized with a fractured vertebra in the neck and partial paralysis.

An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.

An employee was cutting cabinet trim using a table saw when four fingers on his left hand were severed, resulting in hospitalization and amputation.

An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.

A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.

An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.