EATON CORPORATION

A maintenance technician was cleaning a piece of equipment that is used to pump grease when their hand became caught between a pulley and belt on the equipment. The employee sustained a right middle fingertip amputation.

An employee was working on a jet wheel blaster and putting dies into the machine when their thumb was caught between the moving table and a fixed part. The employee sustained a crush injury to the finger.

An employee was maneuvering steel bundles supported by an overhead crane. The employee's right hand was caught under or beside the bundle, and a fingertip was amputated at the last knuckle.

An employee was doing electrical work. An arc flash caused the employee to suffer third-degree burns to the chest and hands.

An employee had three baskets of parts stacked on a work table. The top basket slid off the table and lacerated her right thigh.

An employee was operating a forklift and unloading a truck. After the truck was unloaded, the employee got off the forklift and proceeded to adjust the dock plate with a hook tool. The dock plate slipped and the employee went to adjust the plate with their hand when their left middle finger got caught. Their finger was amputated above the first joint.

An employee was rotating a carbide granulator blade when his finger was caught between the blade and a stationary part of the machine. The employee's right middle finger was partially amputated and they suffered an avulsion to the right ring fingertip.

An employee was using a CNC metal lathe machine in manual mode to check that the thread blocking tool made contact with the jaws. As the employee was manually spinning the spindle, his index fingertip was crushed between the spindle's jaws and the grooving insert, resulting in a fingertip amputation.

During a material handling operation, an employee's fingertip was caught under an air conditioning unit as the unit was lowered onto a cart. The employee's fingertip was amputated.

An employee was removing a bolt from a tractor hub when their right index finger was caught between the hub and the frame. The employee's fingertip was crushed and the employee was hospitalized.

An employee was making repairs to a milling machine located in the mold shop. While using a screwdriver to make adjustments, the machine energized and struck the employee. The employee's right arm was fractured.

An employee was breaking down dunnage to prepare totes and trays to go through a tote washer. A tow motor driver asked the employee to move a cart that was in the way so the tow motor could remove a gaylord. The employee moved the cart and then stepped away from the tow motor. As the employee moved to an area between carts, his right foot got caught by a cart, causing him to twist and fall on top of a cart, landing on the left flank of his torso. The employee suffered a hemorrhage on his left flank.

An employee tripped over a computer cord and fell fracturing their femur.

Three employees were installing a transfer rail in a press. There were two employees holding the rail and the injured employee was at the end of the rail guiding the rail into the bracket. The task was done manually with no mechanical equipment. The employee had their finger at the end of the rail and went to make sure the rail was lined up while the other two employees pushed it into the bracket, causing their finger to become pinched between the rail and bracket. The employee's middle fingertip was amputated. Protective gloves were worn at the time of the incident.

An employee was walking across the dock, interacting with forklift drivers on what was being loaded. A forklift drove forward with a tall load on the forks. The employee was struck by the load (running board/rocker panel rack) on the forklift. The employee sustained several contusions and an injury to their right Achilles tendon that required surgery.

An employee was helping to lift the grating from a floor draining system when the grating slipped and landed on his hand, resulting in the amputation of his right middle finger at the first joint.

A casting machine jammed. An employee's hand was caught in the machine, where a belt line caught and amputated the tip of his finger.

During a workshop meeting in a hotel, an employee heard a drilling noise, so he walked outside to see what it was. An explosion occurred (possible gas line) and his face, ear, and hair were burned. He also fell and sustained a pelvic fracture.

An employee slipped on condensation on a walkway in a parking garage. She fell and suffered a closed fracture to the neck of the left femur.

An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.