Struck by running powered equipment during maintenance, cleaning, testing · Amputations, avulsions, enucleations unspecified
At a glance
Federal OSHA recorded a severe workplace injury
at Eaton Corporation, 4200 Hiway 30 E, KEARNEY, NEBRASKA 68847
on — Amputations, avulsions, enucleations unspecified, affecting the Finger or thumb tip(s), nail(s).
Final narrative
A maintenance technician was cleaning a piece of equipment that is used to pump grease when their hand became caught between a pulley and belt on the equipment. The employee sustained a right middle fingertip amputation.
Amputation Finger or thumb tip(s), nail(s) Machinery unspecified
An employee was working on a jet wheel blaster and putting dies into the machine when their thumb was caught between the moving table and a fixed part. The employee sustained a crush injury to the finger.
An employee was maneuvering steel bundles supported by an overhead crane. The employee's right hand was caught under or beside the bundle, and a fingertip was amputated at the last knuckle.
An employee was attempting to retrieve valves that had fallen below the carriage of an eddy current tester. When he retrieved the valve the carriage of the test machine amputated his left little fingertip.
A temporary employee turned off a planer machine, opened the housing, and began clearing a jam. The machine's spinning blade caught his right hand and degloved the index finger.
An employee was using a tool to remove a rag from a roll on the tube mill. The roll pulled the tool and the employee's right hand into the roll, resulting in a partial amputation of the little finger and a fracture to the index finger.
A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.
More severe injuries in this industry (NAICS 336310)
An employee was pushing automotive suspension material using a material rack. The material started to shift and caught the employee's right little finger, crushing it. The employee suffered an amputation to the finger. The finger was re-attached.
An employee was assembling the gearbox of a lower unit (of a boat motor). They used a handheld electric drill to power the lower unit's gears and inspect the assembly. A gear was out of tolerance, so the employee placed sandpaper in the gearbox to remove any burrs or other material. The employee activated the drill and their left middle finger contacted a nip point between the gears in the unit, resulting in a fingertip amputation.
An employee was reaching for a label and stepped onto a metal piece along rollers and slipped. His leg went down into a gap between the machines and contacted the metal in the gap between the rollers. The employee was hospitalized with the avulsion of skin on his left shin between the ankle and knee, as well as injuries to muscle and ligament.
On June 10, 2025, an employee was driving a forklift west when they were struck by another forklift driving south. The suffered a puncture wound on the right calf.
An employee had just moved a large coil of steel next to another coil on a rack using an overhead crane. They unhooked one side of the sling and held onto it with their right middle finger. As they were raising the crane back up, the sling hung up under the coil, building tension; once it released, it quickly jerked the other side of the sling through the coils along with the last joint of the employee's right middle finger. The finger was amputated to that joint.
An employee was stacking concrete blocks for a concrete bunker. As a block was swinging into place, the employee's left leg was pinched between two blocks, resulting in injuries to his left heel and lower leg.
An employee was climbing a ladder to inspect a vent in a restaurant dining area. The ladder slid out on the floor and the employee fell approximately 12 feet onto the ladder and the floor. He was hospitalized with a dislocated shoulder and a back injury.
An employee was filtering a fryer with a fryer filter machine. After going around the corner and then returning to the fryers, the employee stepped into the filter machine. The hot oil burned the employee's right ankle, and the employee was hospitalized.
An employee was cleaning out corn from a grain bin. The sweep auger in the bin was activated and caught his trouser leg. His leg was pulled into the auger, which injured his calf and caused leg fractures and lacerations.