Direct exposure to electricity, unspecified · Electrical burns, unspecified
At a glance
Federal OSHA recorded a severe workplace injury
at Yesco LLC, 11220 E 53rd Ave, DENVER, COLORADO 80239
on — Electrical burns, unspecified, affecting the hand(s) and arm(s), unspecified.
Final narrative
An employee was making neon signs. He was glass pulling, attained a vacuum in the tube, and pumped the tube with neon. The employee was charging the sign with electricity to check the level of illumination. The employee was trying to attain 300 milliamps in the tube. During bombarding, the milliamp meter malfunctioned and the employee tried to troubleshoot. An arc flash occurred and the employee was shocked and burned on his arms and hands. He also received a laceration to the right elbow and bruising on the right hand.
HospitalizedHand(s) and arm(s), unspecifiedElectric parts, n.e.c.
At 6:30AM on 10/12/16, a crane truck was being setup to load a sign and the truck's outriggers were being setup to stabilize the truck. The injured employee was on the passenger back-side of the truck holding the man basket in place so that the swivel of the basket would not come in contact with tubing on the crane. As he was holding the crane basket, the back outrigger came down and crushed his right foot. Four toes were amputated at the hospital.
An employee was installing a 15-amp breaker in an electrical panel when a 12-gauge ground wire touched the positive busbar of the panel, resulting in an arc flash. The employee sustained a second-degree burn to their left hand.
An employee was repairing an HVAC system in the drop tile ceiling of a conference room when they were shocked, causing them to fall from the ladder. The employee sustained burns to their right middle and ring fingers.
An employee was replacing a contactor inside an electrical panel attached directly to a press. The press itself was receiving power from another main panel. After replacing the contactor, the employee flipped the switch and an arc flash occurred, burning the employee's elbow, bicep, and neck.
An employee was attempting to switch a medium-voltage primary cable and install a 200-amp fuse barrel. The employee contacted the bottom of the switch gear cradle for the fuse barrel, causing an arc blast. The electricity entered the employee s left hand and exited his big toes, resulting in electric shock and burns to the left hand, arm, shoulder, and both feet. The employee was hospitalized.
On December 6, 2023, an employee of Duke Energy was working on a single-phase 120-/240-volt parallel service re-tap when a secondary flash occurred in an underground service. The employee suffered a second-degree burn to the face and was hospitalized.
More severe injuries in this industry (NAICS 339950)
An employee was operating a hand-powered drill to drill holes into plastic clips. The drill bit snagged on a plastic clip and spun the clip around, resulting in an a laceration to her left index finger that required surgical amputation.
An employee was using a table saw to make a dado cut on a piece of wood. The piece of wood contacted the blade, which pulled in the employee's hand. The blade severely cut the employee's left palm.
An employee was shearing sheet metal with a shear machine activated by a foot peddle. When he hit the foot pedal, one of the springs crushed his finger, resulting in a partial fingertip amputation.
An employee was working on a motorized screen when they fell approximately 3 feet from a step ladder to the ground. The employee sustained a face contusion and a fractured jaw.
An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.
An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.
A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.
An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.