Struck by object falling from vehicle or machinery-other than vehicle part · Amputations
At a glance
Federal OSHA recorded a severe workplace injury
at Weyerhaeuser Company, 101 Columbia 14 W, EMERSON, ARKANSAS 71740
on — Amputations, affecting the finger(s), fingernail(s), unspecified.
Final narrative
An employee was raking wood debris from the floor of a step feeder while a second employee was on top of the step feeder using a picaroon to unplug wood from an opening that was full of debris. A piece of wood fell 10 feet through the opening and struck the first employee's left pinky finger, amputating it behind the nail.
AmputationFinger(s), fingernail(s), unspecifiedWood pieces, trim pieces, wood scraps, n.e.c.
An employee performed maintenance on various machines when they began to feel hot and unwell, and they experienced cramping. The employee was hospitalized with heat stress or dehydration.
An employee was sanding a metal shaft on a lathe when his right thumb when under the sandpaper, resulting in the amputation of the distal portion of the thumb.
An employee was performing preventative maintenance on a trimmer and when he went to lower the saw box platform, the pin holding the platform became stuck. The employee hammered at the pin, and when the pin dislodged, the platform swung down and hit the employee. The employee suffered a smashed upper arm with swelling and numbness.
An employee was clearing a jam on a panel stacker when several oriented strand board (OSB) panels fell onto her hands causing a laceration and fracture to the left hand and a laceration to the right ring finger.
An employee was transporting an 800-pound die on a cart from the tool room. The employee was pulling the cart when it struck a metal plate on the floor. This caused the cart to tip forward and the die to slide off the cart. The die struck the employee's left foot and their second toe was amputated.
An employee was using a forklift to load pallets of product on a trailer. He exited the forklift to adjust a pallet by hand. The pallet fell on him, resulting in an injury to the left leg.
An employee was lifting a 500-pound steel counterweight off a pallet using a magnetic hold jib crane. The counterweight detached from the crane and the employee sustained a left foot/toe fracture that required surgery.
An employee was using a pipe wrench to turn a 42-foot-long steel pipe on jack stands to weld the bottom portion. The pipe fell off the stands, striking the injured employee on his left shin. The employee sustained a left leg fracture at the shin area as well as a tibia fracture that required surgery.
More severe injuries in this industry (NAICS 321212)
An employee was working to dislodge a piece of stray veneer from a conveyor. The employee set up a ladder against the machine and climbed the ladder. He placed his left hand on the rail of the conveyor and his fingers were caught in the chain and sprocket assembly that powers the conveyor. Three fingers were amputated. The machine was guarded at the time.
A maintenance employee was changing a shaft on a piece of equipment that had been isolated for repair. While positioning the shaft into place, the shaft fell approximately two feet and pinched the employee's left index finger. The employee suffered a partial amputation of the fingertip without bone loss.
An employee was using a cart to move saw blades. The cart tipped over, striking and pinning the employee under the blades. The employee sustained severe lacerations to their torso and legs that required surgery.
An employee was labeling and writing on the back of a slab of quartz. The material was leaned toward him when the A-frame it was resting on shifted, causing the material to fall onto his right leg and break it.
An employee performed maintenance on various machines when they began to feel hot and unwell, and they experienced cramping. The employee was hospitalized with heat stress or dehydration.
An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.
On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.
An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.
On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.