Fire, unspecified · Second degree heat (thermal) burns
At a glance
Federal OSHA recorded a severe workplace injury
at B & J Hot Oil Services, 2621 West C St., GREELEY, COLORADO 80631
on — Second degree heat (thermal) burns, affecting the face, unspecified.
Final narrative
An employee was trying to light a burn box, but the ignition switch was not working. The employee used a hand torch to ignite the burn box, and the flames flashed in his face, causing first and second degree burns.
An employee was performing oversight for the welding of a pipeline launcher door on a construction project. Two welders were performing arc welding, one on the interior diameter of the pipeline launcher door, and the other on the outside diameter of the launcher door when a flash fire occurred. The injured employee sustained first- and second-degree burns to the face, neck, back, and hands.
While on a scissor lift, an employee was grinding a steel pipe. Sparks from the grinder ignited some nearby rags that had been used to apply coating treatments to the pipe. This fire subsequently ignited the employee's clothing. The employee sustained burns to approximately 46% of their body and was hospitalized.
An employee was working in an area where another company was also working. The other company's employees were using an electric hydraulic pump to remove the bolts of the frac valve. The wiring of the torque wrench and pump unit were then charred and a flash fire occurred. The employee sustained second-degree burns to their face and neck.
On October 17, 2023, an employee was at a sink while using a solvent to unclog a vacuum trap dip tube that contained solids from pinacolborane distillation. During this process, the sink caught on fire and the solvent bottle containing tert-butyl methyl ether fell into the burning sink. The employee attempted to remove the solvent bottle which also caught on fire and suffered burns to their neck and left hand.
An employee was under a railcar cleaning up dust with a vacuum hose. The hose caused a spark that caused a flash fire that ignited the employee's clothing. The employee sustained second- and third-degree burns over 83% of his body.
More severe injuries in this industry (NAICS 213112)
An employee had been cleaning the work area. While lifting a saw, the employee's index finger was lacerated by the saw blade. A tendon was cut and required surgery.
An employee was delivering home heating fuel when bees came from the ground and stung the employee's face, neck, torso, and hands. The employee proceeded to shut off the oil flow before losing consciousness. They were hospitalized due to an anaphylactic reaction.
An employee was using a torch to loosen a bolt on a water trailer. Natural gas was present in the water and it ignited, causing a fire. The employee sustained third-degree burns to their upper leg.
An employee had been conducting crane operations. The employee went to stop a piece of oil and gas equipment for tubular running from falling over to the ground. Their right hand was caught between a rolling ladder and the equipment, resulting in fractures to the index and middle fingers. They were hospitalized and the middle finger required surgery.
An employee was working to install a drive belt on a water pump. He was holding the belt on both sides of the pulley, working to route it over the top. As he pulled down with his right hand, the pulley rotated and the belt slid over it, pulling his left little finger between the pulley and the belt. He suffered an amputation to the fingertip as well as a fracture to the ring finger.
An employee was delivering materials. He was doing his pre-delivery inspection on the roof of the jobsite (a warehouse) when he fell through a plexiglass skylight. He landed on his feet on the concrete floor 14 feet below. The employee sustained fractures to his spine, left ulnar/radius, and right heel. The employee required surgery.
An employee was removing packaging from a roll of printing substrate. The blade of their utility knife got stuck. The employee used both hands to free the knife and the blade partially amputated their left little fingertip.
A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.
An employee was standing on an extension ladder, using a torquing tool to remove bolts that secured blades to a rotor. When the torquing tool activated, its reaction arm came around and pinched the employee's right middle finger against a lifting eye. His fingertip was amputated.