Wilsonart LLC

An employee was dropping off a skid of laminate to be cut at a table saw. The skid was lifted and the forks tilted forward when the stack slid forward and struck the injured employee. The employee was pinned between the laminate and the table of the saw, resulting in a back fracture and a laceration to the liver.

The injured employee and a co-worker were loading a pallet of material onto a rack using a hydraulic lift system. The employee on the south side of the lift picked up the board about 2 inches so the board could enter the rack. The employee on the north side of the lift pressed the travel button to align the board with the rack opening. The injured employee was pinned between the lift and the rack and sustained fractured ribs.

An employee was standing on a 4-by-8 wooden pallet on the forks of a forklift, elevated to the second level of a rack. While pulling a cabinet off the shelf, the employee fell. He landed on the floor 7 or 8 feet below and suffered an injury to his heel.

An employee was pulling a kraft paper roll when a spindle crushed and amputated his right middle finger.

An employee was inspecting the belt of a building exhaust fan on a roof. His left middle finger was pinched between the belt and the pulley and amputated down to the first joint.

An employee was changing a saw blade when the saw machine activated. The employee's left ring and little fingers were amputated.

An employee was clearing a jam from the label cutting machine when their left middle finger was partially amputated.

Two employees were repairing the hydraulic engagement pins on a rented front-end wheel loader. The machine controls were activated to move the attachment pins and an employee's finger was caught between the pins and the bushings. Their right index finger was partially amputated.

An employee was cleaning the conveyor on a piece of equipment when they slipped and their right hand was pulled into the chain sprocket. The employee's fifth fingertip was amputated.

An employee was throwing blankets onto a blanket folding and stacking machine. A blanket got stuck in the machine and she attempted to remove it when the machine contacted her right little finger, resulting in a fingertip amputation.

An employee was working with fiberglass and resins. The employee was hospitalized after having difficulty breathing caused due to chemical exposure.

The injured employee was letting air out of a winding shaft using scissors as a lift table was used to pull the roll off the shaft. The roll/cardboard core slid over the top of the injured employee's scissors and caused the scissors to amputate the employee's little fingertip at the nail base.

An employee was dropping off a skid of laminate to be cut at a table saw. The skid was lifted and the forks tilted forward when the stack slid forward and struck the injured employee. The employee was pinned between the laminate and the table of the saw, resulting in a back fracture and a laceration to the liver.

An employee was using a machine to cut a roll of plastic sheeting. The employee's right hand was at the end of the roll, and when the cutting mechanism of the machine cycled, the employee's right middle and ring fingers were cut, resulting in amputations to both fingers.

An employee was running acrylic film through an automated winding machine which wraps film around a cardboard cylinder core. He noticed that the film had slipped off the winder. He went to the front of the machine to re-attach the film to the winder spool. His fingers got caught between the film and the spool and his left arm was pulled up by the winder spool. The employee was hospitalized with a broken left forearm. Another employee injured their shoulder when pulling the first injured employee out of the machine.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.