Kloeckner Metals

A truck driver was walking on the catwalk of a truck when he slipped and fell to the ground. He sustained a torn right triceps and a lower left leg laceration that required stitches.

An employee was using an overhead crane to lift 25 pieces of 1/8" x 10" x 20 long flat bar material to block it for loading onto a tractor trailer. During the blocking process, the employee was installing the wood block when the chain in the overhead crane slipped out due to the bow of the material at the lifted height. The 25 pieces of material fell, smashing the employee's left gloved thumb between the wood block and the material. When he removed his hand, his thumb tip was amputated.

An employee fell off a truck, breaking his hand.

An employee was pressing the safety latch on a hoist hook and lowering a sheet lifter when his left thumb was caught between the safety latch and eye hook of the sheet lifter.

An employee was helping to move bundles of steel with an overhead crane when the steel fell and struck the employee's right leg.

An employee was using a crane. The hook slipped and a fitting fell onto a finger on the employee's left hand causing a fracture and laceration.

An employee was transporting an 800-pound die on a cart from the tool room. The employee was pulling the cart when it struck a metal plate on the floor. This caused the cart to tip forward and the die to slide off the cart. The die struck the employee's left foot and their second toe was amputated.

An employee was using a forklift to load pallets of product on a trailer. He exited the forklift to adjust a pallet by hand. The pallet fell on him, resulting in an injury to the left leg.

An employee was lifting a 500-pound steel counterweight off a pallet using a magnetic hold jib crane. The counterweight detached from the crane and the employee sustained a left foot/toe fracture that required surgery.

An employee was using a pipe wrench to turn a 42-foot-long steel pipe on jack stands to weld the bottom portion. The pipe fell off the stands, striking the injured employee on his left shin. The employee sustained a left leg fracture at the shin area as well as a tibia fracture that required surgery.

A load of steel angles was being lowered when the lifting chain hit the load, causing it to slide toward an employee. An angle slid and pinched the employee, catching both of their legs between the beams and an angle. The employee suffered two fractured legs.

An employee was on the deck of a trailer helping a customer unload tubes. The employee was working to place a cargo strap on the remaining tubes using a winch bar when it slipped off the tubing, causing him to lose his balance and fall headfirst onto the asphalt lot below. The employee suffered a contusion on his forehead, resulting in hospitalization.

An employee and a customer were unloading two rectangular tubes. The tubes were wrapped together. The plastic wrap was cut so that one tube could be picked up. As the employee was lifting the top tube, the other tube (still connected to the top tube) came down onto his hand and broke two of his fingers. He was hospitalized.

An employee was assisting as a forklift got pipe from a pipe rack. The employee was on one of the forklift's forks as it was raised to the top of the rack, a height of about 15 feet. He fell to the ground and suffered a dislocated and fractured right elbow.

On September 23, 2025, at approximately 7:43 p.m., an employee was using a knife to cut poly banding from a metal coil. The knife slipped, causing a laceration to the inside of their left arm at the elbow joint. The employee was hospitalized and required surgery to repair a damaged vein.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.