Caught in running equipment or machinery during regular operation · Amputations
At a glance
Federal OSHA recorded a severe workplace injury
at Waupaca Foundry Inc, 805 Ogden Street, MARINETTE, WISCONSIN 54143
on — Amputations, affecting the fingertip(s).
Final narrative
An employee placed a casting on a fixture in preparation to start grinding. The employee's glove was caught on the casting flash as the part was being rotated, pulling the employee's fingers into the grinder wheel. The employee suffered fingertip amputations and lacerations.
On March 14, 2025, in the top pick and sort area of the finishing department, an employee was sorting castings on an elevated work platform. They were working with a casting or piece of gating when their right little finger got pinched between the actuator plow and the casting or gating. The employee's fingertip was amputated.
An employee was moving a part from a shaker table to a grinder when their left ring finger was caught between the part and the rotating grinder wheel resulting in amputation of the finger.
An employee was removing slag from the walls of a receiver with a chipping hammer. The employee was caught between a hot metal carrier ladle and chisel bits and suffered a crushing injury to the torso that resulted in a lacerated liver. The employee was hospitalized.
An employee was cleaning out a broaching machine at the end of a shift. The machine actuated, causing amputations to the employee's index finger (to the first knuckle) and ring finger (just above the second knuckle).
On November 17, 2020, an employee was flipping the gating tree and pour cup on the line when the pour cup fell backward and crushed her left index finger on the shaker table resulting in a partial amputation.
An employee was sharpening peeler blades when their shirt was caught in the grinding wheel. The employee sustained tendon damage and a crushed right hand.
An employee was preparing to cut lumber on a panel saw when the clamp engaged and caught the employee's left middle finger, resulting in a fingertip amputation.
More severe injuries in this industry (NAICS 331511)
An employee was realigning two halves of a core box on a core-making machine. Pneumatic pressure released, causing the core box to close on the employee's right thumb. The thumb tip was amputated between the nail and the knuckle.
An employee was performing maintenance/electrical work inside a substation, and used a ladder to access the top of a panel box. The employee fell 8-9 feet from the top of the panel box to the ground. The employee was hospitalized with fractures to their ribs and a shoulder injury.
An employee's hand was caught in a pinch point in the area of a conveyor for a flask running out of a foundry molding machine. The employee's ring finger was crushed and partially amputated at the base.
An employee noticed a block was out of place under the weighted mold frame. The employee used another block to push the block out and replace it. When the block came out, the frame came down on his right ring and little fingers. The employee sustained a fracture and partial amputation to the ring fingertip.
An employee was using a fork truck to move a tub containing molten iron that had been drained from the cupula. The tub tipped over and the molten metal came in contact with water. This caused the molten iron to splash back and burn the employee's upper torso.
The injured employee was assisting five other employees with bracing a wall panel that was being stood up. Another employee slipped on frost on the floor surface. The employees went to evacuate the area in anticipation of the wall panel falling over. The injured employee went to jump through a window opening within the wall panel and their lower half was crushed by the falling wall panel. The employee sustained a fractured pelvis.
An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.
A production sanitation employee was pre-rinsing an incline conveyor and noticed cheese stuck between the belt idler. The employee went to remove the cheese and their glove got caught and pulled their left forearm into the conveyor. The employee's arm was fractured. The machine was not locked out/tagged out at the time.
An employee was on a ladder, taking measurements for a new gutter installation. The ladder slipped out from under him and both he and the ladder fell to the ground. He was hospitalized with seven broken ribs and a broken clavicle.
An employee was unloading a truck for a delivery job. While moving boxes in the truck, the employee tripped over a pallet and fell out of the truck to the ground, resulting in four broken ribs.