General Cable

An employee was performing a welding operation. A die came down and caught the employee's right little finger, amputating the tip.

An employee was working at a wrapper on a recoiler, wrapping a coil with plastic. A pigtail became caught on a pipe; while an employee was pushing it back into a working position, the machine engaged and its rotating bearing hit the employee's left hand. The employee suffered partial amputations to the middle and ring fingers. The machine was unguarded at the time.

An employee was moving reels in a machine. The employee unloaded a full reel from the machine and was rotating an empty reel to be loaded. The employee's left hand was caught between the full reel and the empty one, causing the amputation of the index, middle, and ring fingertips.

An employee was inspecting bad cable at a take-up reel. The employee's left hand was caught between the cable and the reel, causing the amputation of the tip of the little finger.

An employee was about to weld a piece of cable from the east side cable to the west side cable. The west side was already clamped off and the employee was putting the east side into the clamp on the cable welder. As he was lowering the guard, the clamp guard actuated catching his right middle finger in the clamp and amputating the fingertip.

A crew was pulling a 4-inch plastic gas pipe off a reel and straightening it for installation. The injured employee stepped up on the trailer to cut the last band holding the pipe in the coil on the reel. As he turned to step off the trailer, the end of the pipe rotated and sprung out of the cage surrounding the coil, striking the employee on the side of the head and knocking him off of the trailer into the roadway. The employee suffered head trauma that required hospitalization.

An employee and a co-worker were performing a pick inside a clear well. They rigged the skid pan that was full of broken concrete. When lifting, the load began to swing toward a wall. The employee tried to stop the skid pan from swinging and was struck by the pan, resulting in fractures to their left hip and wrist.

The employee had just completed refueling a lattice crane that was breaking up material and was winding the fuel hose back into the fuel truck when he was struck by the catwalk/stairs of the crane. The employee was hospitalized with a laceration to his backside, possible internal bleeding, and a broken hip.

An employee was fusing 10-inch black rubber utility pipes together using a pipe fusion machine and could not get the pipes to set correctly. The employee used a nylon strap attached to an excavator to lift one side of a pipe off a steel plate. As his hand was between two pipes, the pipes came back together, partially amputating two of his fingers.

An employee was lifting four bags of a lime blend weighing approximately 10,000 pounds using a crane. The load swung and pinned the employee against a structural I-beam, resulting in fractures to the hip and pelvis.

An employee was approximately 5 feet up on a ladder while drilling a hole for cable installation. A wasp attacked him. As he was coming down the ladder, he landed flat on his feet on the ground, and his right leg was twisted. The employee sustained a fractured tibia.

An employee had been installing an outside cable line at a residence. The employee became nauseous from working in the heat. The employee was hospitalized with heat exhaustion and dehydration.

An employee tripped at an elevation change while approaching a home. He fell to the ground and hit his head on a rock, suffering a contusion to the left eyebrow and a possible concussion.

An employee climbed to the top of a ladder at a customer's house. The ladder shifted and the employee fell 28 feet to the ground. The employee was hospitalized for a lung contusion and a right foot contusion.

An employee was knocking on a customer's door when two dogs from a neighboring house attacked them, resulting in bite wounds that required hospitalization.

An employee was operating an ironworker (steel punching/shearing) machine. A piece of the tooling broke off and struck the employee's neck; a fragment was lodged in his neck. The employee was hospitalized and required surgery.

On October 25, 2025, an employee was stringing up a new reel of tire tread on a machine. The employee pulled a 6-inch tail and proceeded to spool up the liner. As the machine was jogged to begin the liner wrapping process, the liner caught the employee's glove and pulled their right arm into the liner, causing a fracture to the arm.

An employee was doing a cable change on top of an electric overhead traveling (EOT) crane. They were positioned between the cable drum and the drive shaft. While rotating the cable drum, the employee reached for the new cable that was to be installed. The grease fitting on the drive shaft caught their fall harness and pulled them underneath the drive shaft. The employee was pinned between the drive shaft and two pieces of angle steel, resulting in a fracture to their left hip.

An employee was helping two other employees to push a pallet of tile on a loading dock. He suffered a broken fibula and was hospitalized.

On October 5, 2025, an employee was pulling a pressure washer hose when it it disconnected from the cooker. The employee was struck by jets of high-pressure water, resulting in lacerations to their left thigh requiring surgery. The employee was hospitalized.