Lexicon, Inc

An employee was using a sleever bar to move a checker plate into place and secure it to the floor of a structure in the melt shop. The sleever bar became stuck and the employee used his left hand to lift the checker plate up enough to free the sleever bar. Once the bar was freed, the checker plate came down and pinched his left index finger between two pieces of plate. The employee suffered an amputation of soft tissue at the fingertip, which required hospitalization.

On May 16, 2025, an employee crossed over a stand to support a wide flange beam they were fabricating. The beam rolled over onto their lower right leg and foot, resulting in fractures.

An employee was placing a steel I-beam when it became stuck and would not settle onto the flanges. The employee was moving the beam and when it became unstuck and crushed the fingers on his left hand. The employee was hospitalized and required surgery.

The injured employee was assisting a crew to install a crane rail on an overhead crane girder. He was on the 40' x 10' grated surface between the crane rails positioning himself to receive the end of the crane rail. The crane rail was being pushed on rollers toward the employee's location and as he tried to pry the end of the crane rail up to get it on top of the next roller, he lost his balance and fell 36 feet to the ground below. The employee sustained fractures to their right ankle, pelvis, and left arm. The employee was wearing a personal fall arrest system, but was not tied off at the time.

An employee was installing drive shafts on an overhead crane. The drive shaft was rigged about 17 feet up with a wire rope choker. The drive shaft began slipping through the rigging, when it slid down and struck the injured employee's hard hat. He was knocked to his knees and landed on his right knee. The employee sustained an amputation to the right leg below the knee.

An employee was assisting with pipe on a drilling rig. The slips came down and landed on the employee's left foot fracturing four metatarsals.

Two employees were struck by the rotary table of a drilling rig while installing caisson. Employee 1 suffered multiple fractures, internal injuries, and head trauma. Employee 2 suffered multiple fractures, internal injuries, spinal injury, and head trauma.

Employees were felling hazard trees. The injured employee was conducting 'bucking' operations to saw a tree from the road when the tree kicked-back, pinning him against the ground and fracturing his left femur. The employee was hospitalized and required surgery.

An employee was greasing tongs on a work-over rig. The tongs lacerated one of the employee's fingers.

An employee was chaining a vehicle when he had to change tools and the compressor. As the compressor was being charged, the employee stepped near the vehicle to make sure the compressor was attached. Then, he instructed a co-worker to lower the compressor. His right hand was on the compressor and under the chain, causing his ring finger to be crushed.

On October 21, 2025, an employee was operating a saw when a pneumatic clamp caught their right middle finger. The employee suffered a partial amputation to the finger.

An employee completed an end cut on a metal shim and started transferring the metal shim from the saw conveyor to two saw horses in the area. The employee set one end of the shim (7 feet long x 8 inches wide, weighing 218 pounds) on one of the saw horses, then slid the other end onto the other saw horse and the shim fell from the first saw horse. The employee's left index fingertip was pinched between the saw horse and the shim, resulting in a skin avulsion. The fingertip was amputated later.

An employee was using a crane to move a 44-foot, 3,343-pound I-beam. As the beam was moving west, it straightened out (north to south), beginning to swing south toward the northwest corner of a building. The crane then sent the beam southward, directly toward the corner of the building. The beam caught the tips of the employee's left index, middle, and ring fingers against the building. The last joints of the middle and ring fingers were amputated, and the last joint of the index finger was partially crushed.

An employee was moving steel beams with an overhead crane when the bundle struck a bollard and became unstable. As the employee reached to stop the material from shifting, his thumb was pinched in-between the beams, resulting in a partial amputation.

An employee was rigging a steel joist to be lifted by a crane. The joist fell and pinned the employee against the concrete ground. The employee sustained fractures to multiple ribs, his right arm, right tibia, and an open fracture to his right ankle, as well as a dislocated right hip.

An employee was working to deliver mail to an apartment building. She was waiting for a customer to move, to obtain clearance to the mailboxes. The door swung inward and closed on her right little finger. The top half of her finger was surgically amputated.

An employee fell from a step ladder while reaching for a tie-off point. He impacted the ground, and landed on his bolt bag which contained tools. The employee was hospitalized with fractured ribs, and a lacerated spleen and kidney.

On October 30, 2025, an employee was working to adjust a stackable metal shipping container. As the container dropped into place, it caught the employee's hands in an area between the upper and lower cross-members. The employee suffered a laceration to the left ring finger that required stitches, bruising to the right ring finger, and fractures to the right middle finger that necessitated medical amputation of the fingertip.

An employee was moving a scissor lift through a doorway. The employee was pinned between the scissor lift and the doorframe, sustained a back injury, and was hospitalized.

An employee was setting up communication equipment for a meeting. They were walking and tripped over a speaker on the ground. The employee sustained a leg injury.