BECTON DICKINSON

An employee was inspecting trays as they came out of the descrambler machine. The employee went to reach for a damaged tray when his right index finger was caught between the tray and a sidepiece of the conveyor line, resulting in a fingertip amputation.

Two employees were removing a screw from a high-speed injection molding machine. As they were removing the screw tip, pressurized molten plastic was released through an opening around the screw tip which resulted in both employees being burned by the molten plastic. They sustained burns to the forehead, right neck, face, right arm, and right hand. One employee was hospitalized.

An employee was troubleshooting a packaging machine and adjusting the media when his left index finger was caught in the perforation blade, resulting in a traumatic amputation of the distal phalanx.

An employee was threading a new roll of bags into the midstream bagger machine. The jaws of the machine include a heat seal and cutters. The machine activated and the jaws caught his finger resulting in the amputation of the left index fingertip.

Maintenance employee was responding to a jammed machine on line #9. The employee reached into the machine to remove the jam. The machine cycled, feeding another tray that pinched his right ring fingertip between the tray and the frame of the machine, resulting in the tip being amputated.

An employee was changing a saw blade when the saw machine activated. The employee's left ring and little fingers were amputated.

An employee was clearing a jam from the label cutting machine when their left middle finger was partially amputated.

Two employees were repairing the hydraulic engagement pins on a rented front-end wheel loader. The machine controls were activated to move the attachment pins and an employee's finger was caught between the pins and the bushings. Their right index finger was partially amputated.

An employee was cleaning the conveyor on a piece of equipment when they slipped and their right hand was pulled into the chain sprocket. The employee's fifth fingertip was amputated.

An employee was throwing blankets onto a blanket folding and stacking machine. A blanket got stuck in the machine and she attempted to remove it when the machine contacted her right little finger, resulting in a fingertip amputation.

On August 15, 2025, an employee was in a small room right before the exit. The door in the little room was locked. The employee climbed over a wall and hopped down to the other side, falling and resulting in a twisted right ankle. The employee was hospitalized.

On August 14, 2025, an employee was assembling cables using a molding machine. When the machine was engaged, the mold came down and caught the employee's left hand, amputating three fingers.

On August 8, 2025, an employee was operating a table-top injection molding machine. He refilled the barrel of the machine with resin and began a pack procedure in which the plunger of the machine moved into the barrel to compress plastic pellets into the mix. The plunger caught and amputated his fingertip.

An employee was entering the manufacturing area when their finger became caught between a door and the door frame, resulting in an amputated finger.

An employee was working to move a pallet jack that had gotten stuck between the dock and the trailer. When the equipment was loosened, it struck the employee, throwing them backward onto the ground. The employee sustained fractured ribs and injury to their spleen and liver.

An employee was stacking concrete blocks for a concrete bunker. As a block was swinging into place, the employee's left leg was pinched between two blocks, resulting in injuries to his left heel and lower leg.

An employee was climbing a ladder to inspect a vent in a restaurant dining area. The ladder slid out on the floor and the employee fell approximately 12 feet onto the ladder and the floor. He was hospitalized with a dislocated shoulder and a back injury.

An employee was rappelling down a tree. When he was most of the way down, he fell on the ground and suffered a broken pelvis.

An employee was filtering a fryer with a fryer filter machine. After going around the corner and then returning to the fryers, the employee stepped into the filter machine. The hot oil burned the employee's right ankle, and the employee was hospitalized.

An employee was cleaning out corn from a grain bin. The sweep auger in the bin was activated and caught his trouser leg. His leg was pulled into the auger, which injured his calf and caused leg fractures and lacerations.