Austin Bridge & Road, LP

An employee was obtaining a lab sample of AC oil for an asphalt mix design when oil contacted his heat protection glove gauntlets. The employee removed the gloves when the oil contacted both his palms and six fingers, resulting in second-degree burns.

A crew stopped operations when rainfall started. The injured employee was putting away tools in the tool truck bed while a pickup truck was driving to the end of the location. When the pickup truck applied the brakes, the mud caused the vehicle to slide. The injured employee was caught between the rear bumper of the tool truck and the front bumper of the sliding pickup truck. The employee sustained fractures to their pelvis and femur.

The injured employee and a co-worker were removing the bolts supporting a section of formwork. As the injured employee went to access the top of the formwork, they fell through the formwork. The employee fell 20 feet to the ground and sustained broken vertebrae and multiple contusions.

An employee had been measuring a head gate. The slide gate was being hoisted out of an aeriation basin box when the edge of the slide gate caught on the metal grating at the top of the box. The grating became dislodged and fell, contacting the lower right leg of the employee. The fibula and tibia were fractured.

An employee was removing asphalt from a buggy auger. The employee's right index finger was amputated in a shear point between the spinning auger and the machine's frame. The auger was not locked out at the time.

An employee was on a step ladder applying glue to a panel when the ladder fell apart, causing the employee to fall to the floor. The employee sustained rib fractures.

On December 5, 2023, an employee was loading product onto a freight elevator when the elevator fell with the employee inside. The employee sustained a right leg injury.

On 11/28/2023, an employee was loading a cart with supplies to be delivered to a restaurant. He stepped onto a ramp to get into the back of a truck but the ramp fell to the ground, causing the employee to fall as well. The employee was hospitalized with a fractured ankle.

An employee was climbing a 16-foot fiberglass extension ladder to access a roof so they could take measurements for a roofing quote. The employee had partially ascended the ladder when the ladder broke in half. The employee's foot was caught in a ladder rung resulting in an ankle fracture that required surgery.

An employee was replacing a heating, ventilation, and air conditioning (HVAC) valve in a ceiling while standing on a ladder. The ladder collapsed while the employee was descending, causing them to fall to the floor. The employee sustained a broken wrist.

An employee was operating a battery-powered broom to clean demolition debris off the top of the outermost bridge girder. The girder was approximately 11 feet above the demolition scaffold below. The employee fell approximately 8 feet to wind bracing below. The employee was hospitalized with a pelvis/tailbone fracture. Fall protection was in place at the time.

An employee was cleaning out an inlet pipe in a stormwater structure. The employee stepped back, fell into the pipe, and landed on concrete 13 feet below, at the bottom of the structure. He suffered a broken back.

A concrete batch plant operator was assisting with clearing spoil piles using a skid steer. The skid steer backed into a stationary screen plant. The employee's left little finger was crushed between the controls of the skid steer and the screen plant, resulting in a fracture and laceration. The employee's finger was surgically amputated.

An employee was operating a roller and paving a small pathway next to a pavilion. The ground was on a slight pitch, causing him to reach up toward the roll cage to stabilize himself. His right fifth finger was pinched between the roll cage and the rafter of the pavilion. The employee sustained a partial degloving injury with partial traumatic amputation.

An employee was working with paving equipment and heard a noise on the opposite side of the machine he was working on. When the machine stopped, the employee went to the opposite side and crouched down to investigate the noise. A mini track loader backed up and drove over the employee's leg. The employee sustained fractures to their lower leg, ankle, and foot.

After cutting a slab of beef short ribs, an employee turned to grab the pieces he had cut and his right hand contacted the saw blade. The employee sustained an amputation to his right index finger.

An employee was unloading a carpet pad from a truck when they fell from the truck dock to the concrete below, resulting in five fractured ribs and an injury to their left lung.

An employee was inspecting flares processes. The employee received burns to the front side of the body, face and arm from the flares.

An employee was removing plastic material from a production line when the machine cycled and amputated his left index, ring, and little fingers.

An employee was walking up a walkway to enter a building through the back entrance when she tripped over the lip of the cement ramp. The employee fell and sustained a fractured right hip.