Compressed or pinched by shifting objects or equipment · Fractures
At a glance
Federal OSHA recorded a severe workplace injury
at Alfa Laval Inc., 1201 S. 9th Street, BROKEN ARROW, OKLAHOMA 74012
on — Fractures, affecting the face, unspecified.
Final narrative
An employee was securing the air seal on a motor mount when another employee, who was attempting to lower a fan assembly, loosened the come-along on the load and the fan assembly shifted, pinning the injured employee into the motor mount. The employee's head was crushed, breaking several bones in his face.
HospitalizedFace, unspecifiedMachine and appliance parts, n.e.c.
An employee was working in the hydro department putting a bolt into a metal header when he struck his hand and right index finger on the metal header. He was hospitalized for an infection.
An employee was using a pin press machine to put pins in the back of a heat exchanger louver blade. His right hand was caught between the blade and a hydraulic component, causing a partial amputation to the index fingertip.
An employee was using a hand-held drill to ream a hole in a sheet metal bracket held in a vice. The injured employee was attempting to remove a wire loop from the hole being drilled when his glove was caught in the bit. The glove pulled the middle finger on his left hand into the bit, causing cartilage and tendon damage that resulted in a finger amputation.
An employee was operating a forklift and unloading a truck. After the truck was unloaded, the employee got off the forklift and proceeded to adjust the dock plate with a hook tool. The dock plate slipped and the employee went to adjust the plate with their hand when their left middle finger got caught. Their finger was amputated above the first joint.
An employee was rotating a carbide granulator blade when his finger was caught between the blade and a stationary part of the machine. The employee's right middle finger was partially amputated and they suffered an avulsion to the right ring fingertip.
An employee was using a CNC metal lathe machine in manual mode to check that the thread blocking tool made contact with the jaws. As the employee was manually spinning the spindle, his index fingertip was crushed between the spindle's jaws and the grooving insert, resulting in a fingertip amputation.
During a material handling operation, an employee's fingertip was caught under an air conditioning unit as the unit was lowered onto a cart. The employee's fingertip was amputated.
An employee was removing a bolt from a tractor hub when their right index finger was caught between the hub and the frame. The employee's fingertip was crushed and the employee was hospitalized.
More severe injuries in this industry (NAICS 332410)
An employee was using a vertical band saw to cut a thick piece of rubber material. While being cut, the material shifted, causing the employee s right hand to contact the moving blade. The employee's thumb was amputated below the knuckle. The employee was hospitalized, undergoing surgery.
An employee was laying underneath a cooler block while jacking up the tie bar to secure it to horses when the cooler block fell off the horses and onto the employee, resulting in several fractures to the pelvis, clavicle, wrist and tailbone.
An employee was climbing a ladder on a water cooling tower when they fell approximately 15 to 20 feet to the ground, resulting in a fractured left elbow.
An employee was preparing to sand a metal shaft that was loaded into a lathe when his left arm became entangled in the machine. The employee sustained several broken bones.
An employee was removing the banding from a load of mechanical supports, when one fell forward onto his left leg. The employee sustained a laceration to the lower leg and was hospitalized.
An employee was helping to move a 1,300-pound coil on a cart. The steel caster hit a crack in the concrete, the weld holding the caster onto the cart broke, and the coil and cart tipped over onto the employee. He was hospitalized with a laceration on his forehead and a pelvic fracture on his right side.
An employee was working in the food service warehouse when he experienced chest pain, difficulty breathing, and lost consciousness. The employee sustained carbon monoxide poisoning.
An employee was cutting a piece of metal rod with a metal cutting machine. His right middle finger became caught between the rod and the machine's table. The employee's fingertip was partially amputated.
An employee was working at her desk. She went to stand up and fell to the floor beside the desk. The employee sustained a hip displacement and required surgery.
An employee was processing wood boards at a chop saw when the saw malfunctioned and the blade cut her left hand and fingers. She was hospitalized and her little finger was surgically amputated.